N7201A618E00_0309.pdf - 第134页
NPM–W 2 EJM7DE-MB-02 -1T-00 Parts Re cognition Error Error Message Troubleshooting 2-1-3 Single stop er r or 33 Error Code Error Message Cause Inspection and Solution Detected comp onent size in L (X) direction is invali…
NPM–W2 EJM7DE-MB-02-1T-00
Parts Recognition Error
Solutions to errors
Error Code
Error Message
Cause Inspection and Solution
Detected component center
position is incorrect.
- Component detection
position is beyond the
specified area range.
- With 1-way lead array
component^ component
center position calculated
from lead column is out of
recognition screen.This
error occurs also when
improper judgment was
determined after the
following recognition
options were added.
Ans22(51): Center area
check Ans22(52):
Protrusion check
Ans22(53): Adjoining mount
check
(Recognition error -
Component recognition
position)
Take any of the following measures:
1) Check the component pickup
position and pickup
condition.Make sure the
component pickup position is not
placed at the center and the
component is not likely to be in the
slanted pickup posture.
2) When the recognition option for
checking the recognition result
position is specified, check the
allowable range.
43022
2-1-3-63
NPM–W2 EJM7DE-MB-02-1T-00
Parts Recognition Error
Error
Message
Troubleshooting
2-1-3
Single stop error 33
Error Code
Error Message
Cause Inspection and Solution
Detected component size in
L (X) direction is
invalid.Component size in L
direction differs widely from
registered data.
(Recognition error -
Measurement result in size L
direction)
Take any of the following measures:
1) Check the component outer
shape size and the distance of
shapes in L (X) direction.For
components with electrodes at
both sides, check the distance
between the electrodes.In case of
a recognition error of Ans25
(30~39), an error is detected when
performing detailed check of the
component size.If the component
size varies widely and variation
can be tolerated with actual
components, specify the
Recognition option: Component
size limit.
2) Check the image status of the
component at both sides.If the
shape of the ends like J-lead
component or curved component
is unclear on the image, adjust the
lamp value and correct the image
status.(At this time, the side
lighting is effective.)
3) Check the component pickup
position and pickup
condition.Make sure the
component pickup position is not
placed at the center and the
component is not likely to be in the
slanted pickup posture.
43025
2-1-3-64
NPM–W2 EJM7DE-MB-02-1T-00
Parts Recognition Error
Solutions to errors
Error Code
Error Message
Cause Inspection and Solution
Detected component size in
W (Y) direction is
invalid.Component size in W
direction differs widely from
registered data.
(Recognition error -
Measurement result in size
W direction)
Take any of the following measures:
1) Check the component outer
shape size and the distance of
shapes in W (Y) direction.For
components with electrodes at
both sides, check the distance
between the electrodes.In case of
a recognition error of Ans26
(30~39), an error is detected when
performing detailed check of the
component size.If the component
size varies widely and variation
can be tolerated with actual
components, specify the
Recognition option: Component
size limit.
2) Check the image status of the
component at both sides.If the
shape of the ends like J-lead
component or curved component
is unclear on the image, adjust the
lamp value and correct the image
status.(At this time, the side
lighting is effective.)
3) Check the component pickup
position and pickup
condition.Make sure the
component pickup position is not
placed at the center and the
component is not likely to be in the
slanted pickup posture.
43026
2-1-3-65