N7201A618E00_0309.pdf - 第95页
NPM–W 2 EJM7DE-MB-02 -1T-00 Nozzle Inst. Err (Vacu) Nozzle Remove Err (Vacu) Nozzle Missing Err (Hd) Unnecessary Nzl Err (Hd) Solutions to errors Error Code Error Message Cause Inspection and Solution A nozzle was instal…
NPM–W2 EJM7DE-MB-02-1T-00
Nzl Chg Mark Recog Err
Nzl Changer Close Err
Nozzle Changer Open Err
Error
Message
Troubleshooting
2-1-3
Single stop error 13
Error Code
Error Message
Cause Inspection and Solution
Nozzle changer failed to
open within the prescribed
time.
(Single stop error occurred.)
Choose [Machine] - [Adjust] - [All] -
[Output confirm] and open/close the
nozzle changer. Check for proper
movement. If stopped or caught on
the way, perform cleaning.
40376
Nozzle changer failed to
close within the prescribed
time.
(Single stop error occurred.)
Choose [Machine] - [Adjust] - [All] -
[Output confirm] and open/close the
nozzle changer. Check for proper
movement. If stopped or caught on
the way, perform cleaning.
40377
Failed to recognize the mark
of nozzle changer.
(Single stop error occurred.)
Make sure the mark of the nozzle
changer is free of dirt or dust.Make
sure the light of the head camera is
lit during recognition of nozzle
changer mark. If not lit, contact
PFSC.
40378
2-1-3-24
NPM–W2 EJM7DE-MB-02-1T-00
Nozzle Inst. Err
(Vacu)
Nozzle Remove Err
(Vacu)
Nozzle Missing Err
(Hd)
Unnecessary Nzl Err
(Hd)
Solutions to errors
Error Code
Error Message
Cause Inspection and Solution
A nozzle was installed on a
head where it should not
have been.
(Single stop error occurred.)
Remove the applicable nozzle from
the head.
40379
No nozzle on a head where
the proper nozzle was
supposed to be installed.
(Single stop error occurred.)
Choose [Machine] - [Adjust] - [Head]
- [Nozzle exchange] and match the
mounting condition of the actual
nozzle and memory on the machine.
40380
Any of the following causes
is likely:
1) Nozzle failed to be
changed properly due to
dirt or dust on the nozzle^
nozzle holder or nozzle
changer.
2) Shutter is at fault.
(Single stop error occurred.)
Clean the nozzles, nozzle holders
and nozzle changer. If the error
persists, contact PFSC.
40381
Any of the following causes
is likely:
1) Nozzle failed to be
changed properly due to
dirt or dust on the nozzle^
nozzle holder or nozzle
changer.
2) Shutter is at fault.
(Single stop error occurred.)
Clean the nozzles, nozzle holders
and nozzle changer. If the error
persists, contact PFSC.
40382
2-1-3-25
NPM–W2 EJM7DE-MB-02-1T-00
Nozzle Missing
(Rack)
Unnecessary Nzl
(Rack)
Cart Offset Recog Err
Cart Offset Range over
Clogged Nozzle Detect
Error
Message
Troubleshooting
2-1-3
Single stop error 14
Error Code
Error Message
Cause Inspection and Solution
Clogged nozzle detected.
(Single stop error occurred.)
Clean the applicable nozzle.
40383
Recognition result of cart
offset mark is beyond the
specified range.
(Single stop error occurred.)
Make sure the feeder cart is set to
the machine in the upright position.
If slanted, detach the feeder cart
once and attach it again.
40384
Failed to recognize the cart
offset mark.
(Single stop error occurred.)
Make sure the cart offset mark is
free of dirt or dust.
40385
A nozzle was detected on a
head where it should not
have been^ in nozzle check
processing of the head unit.
(Single stop error occurred.)
Remove the applicable nozzle from
the head.
40386
A nozzle was not detected
on a head where it should
have been^ in nozzle check
processing of the head unit.
(Single stop error occurred.)
Choose [Machine] - [Adjust] - [Head]
- [Nozzle exchange] and match the
mounting condition of the actual
nozzle and memory on the machine.
40387
2-1-3-26