天龙M10 M20_中文手册.pdf - 第480页

3132 %s Setup error Place %m in Pallet %d2 of Magazine Rack Tray component setup error Set up the proper tray 3113 The PCB on the conveyor may not be reloaded. Remove the PCB. At the start of production, the PCB was dete…

3094

为了防止贴装头冲突

请千万不要拆卸正在生产中的送料器

3075

Pallet information of %s and pallet positions in the

stocker do not match. The machine recovered

automatically. Check pallet positions in the stocker.

3076

Head stops while waiting for completion of CTF/FTF tray

setu

3077

Head will start traveling after completion of CTF/FTF

tra

setu

3078

The component cannot be put back to the tray for reuse

because %s is in Nonstop tray setup mode. To cancel the

mode

ress Setu

switch.

Press Setup switch to allow CTF/FTF to supply

components.

3079

中断激光校正

3080

激光校正中出现异常

3081

激光治具水平检查错误治具没被设置为水平。请确认设置状态。

3082

激光高度比例检测错误重新调整激光头的安装状态，再次进行实施自动校正。

3083

激光高度检测范围错误重新调整激光头的安装状态，再次进行实施自动校正。

3084

激光Z偏差检测错误重新调整激光头的安装状态，再次进行实施自动校正。

3085

激光XY偏差检测错误粗调整XY偏差后，再次进行实施自动校正。

3086

激光不可检测检查错误确认激光投光部的赃物或异物后，再次进行实施自动校正。

3087

送料器的吸取高度超出极限值，而无法设置此站。%s-%d1 %m

%v2mm < %v3mm

To set the feeder at a feeder station, 'ST-F1 to 13 on

M10', or 'ST-FR24 to 36 or ST-FL1 to 13 on M20', feeder

pickup point height, "sum of Pickup 'Z offset' + Feeder

'Feed height' + Package 'Height'" must be 5mm or less.

(Minus Z offset is not added.)

3088

送料器的突起物高度超出极限值，而无法设置此站。%s-%d1 %m

%v2mm < %v4mm

To set the feeder at a pickup station, 'ST-F1 to 13 on

M10', or 'ST-FR24 to 36 or ST-FL1 to 13 on M20', sum of

the device max height and the feeder height must be 5mm

or less.

3089

%s 通信出错

3090

%s 伺服器出错

3091

READY %s X,%d1,Y,%d2,Z,%d3,%d4,%d5,%d6,%d7,%d8

3092

READY %s R,%d3,%d4,%d5,%d6,%d7,%d8

3093

点胶针的安装角度超出容许值。点胶头%d1 偏移量: %v2 容许

值

: %v3

请重新安装点胶针。

3094

%s-%d1 The feeder is mounted while the machine is

runnin

. Feeder ID %d3-%d4 CFB ID%d5

为了防止贴装头冲突

请千万不要拆卸正在生产中的送料器

，。

3095

%s-%d1 The feeder is removed while the machine is

running. Feeder ID %d3-%d4 CFB ID %d5 (The F1/F2 feed

button was

ossibl

ressed.

)

为了防止贴装头冲突，请千万不要拆卸正在生产中的送料器。

3096

%s-%d1送料器%m的元件间距，从%d2mm变更为既定值

3097

%s-%d1送料器%m的元件间距，从既定值变更为%d3mm

3098

%s-%d1送料器%m的元件间距设定为既定值

3099

%s-%d1送料器%m的元件间距设定为%d2mm

3100

摄像时的加速度和速度取得失败,其图像处理结果判定为NG %m

贴装头

%c1

3101

点胶吸嘴的长度测定失败。贴装头%d1 请确认点胶吸嘴的安装状态。

3102

点胶数据的偏差值超出测试点布站的范围点胶数据的偏差值应小于测试点布站的范围。

3103

Component is placed out of PCB %m Head%c1 Row:%d5

Offset:%d6

Check PCB size, placement point, component data,

selected nozzle

and ima

e data.

3104

Placement error reaches limit count. %m Head%c1 Row:%d5

Offset:%d6

Check PCB size, placement point, component data,

selected nozzle

and ima

e data.

3105

Cannot save a log file.

Shortage of disk space or cannot connect a network

drive.

3106

Cannot drive because version of the right and the left

servo am

lifiers differ. Y1-AMP:%X1 Y2-AMP:%X2

Use X and Y Servo amplifiers of version E4.001.

3107

Failed to capture the pickup point. Row:%d1 Offset:%d2

Check the Pickup point status and the Component image

data.

3108

Extra time was needed to start stable Laser check.

%d1msec

3109

IC component feeding device is out of components or a

malfunction occurred in the device.

Please check IC component feeding device.

3110

Diameter of each dispensing point of multi-nozzles

cannot be compensated to the target diameter. One

dispensing diameter exceeds the maximum acceptable

diameter and another dispensing diameter falls the

minimum acceptable diameter.

Please check the target diameter of each dispensing

point.

3111

Height Check NG %m %d2th row Result:%v3 Tolerance:%v4

Head%c1 Row No.:%d5 Re

eat Offset:%d6

Check the component configuration and position.

3112

Height Check NG reached retry limit %m Head%c1 Row

No.:%d5 Re

eat Offset:%d6

Check the component configuration and position.

3132

%s Setup error Place %m in Pallet %d2 of Magazine Rack

Tray component setup error Set up the proper tray

3113

The PCB on the conveyor may not be reloaded. Remove the

PCB.

At the start of production, the PCB was detected at an

improper position to reload. Remove the PCB and Restart

the

roduction.

3114

Adjusted offset Values of Dispense Nozzle Head:%c1

le:%d2 X:%d3 Y:%d4 T:%d5

3115

Height of the Quick Clamp is not proper. Checked %v1

Set Hei

ht %v2

Check the Quick Clamp motion. Check that no obstacles

between the

uick Clam

and the conve

or.

3116

Differences of check results of Laser1 and Laser2

exceed the tolerance. 1st:%v1 2nd:%v2 Tolerance:%v3

Check the lasers installation status.

3117

The Reject Conveyor %c2-%d3 in Pickup Data No. %d6 is

full or not installed.

Remove components and press the RESET button. Or

install the Re

ect Conve

or at the

er station.

3118

The conveyor width was changed after Push up pins were

located. Located %v1mm, Current %v2mm, Tolerance +/-

%v3mm

Collect the Pushup Pins manually.

3119

Push-up pin location is the same as the last time. The

rocess has been ski

ed.

3120

No feeder in the pickup data is not mounted. The total

feeder number is %d2.

3121

%s-%d1 Feeder is not mounted on the Station. %m

3122

%s A pallet exits in the stocker. Pallet-%d1

The stocker is for the pallet at the pickup position

now. Remove the

allet.

3123

%s The tray cannot move to the pickup point while trays

are in setup mode. To cancel the mode, press SETUP

switch.

Press SETUP switch to allow CTF to supply components.

3124

%s The pallet pickup position exceeds the tolerance. Move the pallet into the stocker.

3125

%c3 head is selected for %c2 row. Head%c1

Actual head configuration and HEAD/ANC Setup info in

the s

stem

arameter must be the same.

3126

Height Check OK %m %d2th row Result:%v3 Tolerance:%v4

Head%c1

3127

An error occurred while Quick Clamp is moving.

Check no components are bitten. Check the cylinder

motion.

3128

An error occurred while Push-up Plate is moving. Check the cylinder motion.

3129

Parameter has been changed. Restart the machine to

erate.

Shut down the machine once.

3131

CTF type is duplicated. %s Type-%m Use a different type of CTF.

3132

%s Setup error. Place %m in Pallet %d2 of Magazine Rack

%d1.

Tray component setup error. Set up the proper tray

com

onent in the ma

azine rack.

3133

%s Setup error. Place %m in Pallet %d2 of Magazine Rack

%d1.

Tray component setup error. Set up the proper tray

com

onent in the ma

azine rack.

3134

%s Support Bar of Magazine Rack %d1 is closed. Open the support bar of the magazine rack.

3135

%s Support Bar of Magazine Rack %d1 is closed. Open the support bar of the magazine rack.

3136

An error occurred while %s servo system was operating. Check the CTF status.

3137

An error occurred while the pallet is moving into %s. Check the CTF status.

3138

%s Error occurred during operation. (%e) Check the CTF status.

3139

%s cover lock timeout Check the CTF status.

3140

%s cover lock timeout Check the CTF status.

3141

%s cover is open. Check the CTF status.

3142

%s cover is open. Check the CTF status.

3143

%s Component shortage (Magazine Rack %d2, Pallet %d3) Replenish the components.

3144

Components are running out. %s (Magazine Rack %d2,

Pallet %d3

)

Remain count: %d4

The number of reing components reached "Shortage Alarm"

entered in the

icku

data.

3145

%s Pallet is found in the magazine. Magaine Rack %d1,

Pallet %d2

Remove the pallet. The pallet currently at the supply

area will be movin

back to this

lace.

3146

%s Pallet is found in the magazine. Magazine Rack %d2,

Pallet %d3

Check the CTF status.

3147

%s No pallet in the magazine. Magazine Rack %d2, Pallet

%d3

Check the CTF status.

3149

%s Replace the Magazine Rack %d1. 请进行供给元件。

3165

Safety protection system worked on %s.

Press CLEAR switch to stop the alarm. If the problem

cannot be cleared

16．点胶机

16-1

16 点胶机

 螺杆式点胶机