3OM-1075-002.pdf - 第66页
(C02) Placement Data (P) (C02_01) Unit Control Select one of the following options to determine whether the selected placement data (U01, U02, ..... Un) should be used. In normal cases, select "Placement". Plac…
2.5 Placement Data
Fig. 3B88 Edit Window (Example)
(C01) Placement Data Un
(C01_01) Selection of Placement Data Group
Select one of the following tabs (placement data groups) in
one pattern program.
U01 : First Placement Data Group
U02 : Second Placement Data Group
È
Un : Up to 99 placement data groups can be specified.
Fig. 3B89 Example of Placement Data (TIM-X100R)
(a) "U01" is used in normal cases.
(b) The operation and feeder location data are used commonly.
(c) Refer to "2.1 Types of P.C.B.’s and Required Data" and "3.
Example of Pattern Program Creation" for details.
0206-002 2-46 AHB01EDTP
2.5 Placement Data
(C02) Placement Data (P)
(C02_01) Unit Control
Select one of the following options to determine whether the
selected placement data (U01, U02, ..... Un) should be used.
In normal cases, select "Placement".
Placement : The placement data of the selected unit
(group) becomes valid.
Bypass : The placement data of the selected unit
(group) becomes invalid.
Offset X [mm], Offset Y [mm]
Set the offset values for all placement coordinates X and Y,
the unit P.C.B. recognition coordinates, and the local P.C.B.
recognition coordinates in the placement data (P-data).
Unit: mm
Data Input Range
X: -99.99 to +99.99 Y: -99.99 to +99.99
(a) Use "00.00" (zero) in normal cases.
(b) Note that these offset values do not give any effect to the
coordinates (X [mm] and Y [mm]) of "A02_02 P.E.C. rec-
ognition mode Global".
Offset Z
Set the offset value for all placement angles (Z=Theta) in
the placement data (P-data).
Data Input Range
-99.99 to +99.99
Use "00°00′" (zero) in normal cases.
Offset H
Set the offset value for all placement height "H" in the place-
ment data (P-data).
Data Input Range
-9.99 to +9.99
Use "0.00" (zero) in normal cases.
0206-002 2-47
AHB01EDTP
2.5 Placement Data
Fig. 3B90
Placement
Unit Control
Offset X [mm]
Fig. 3B91
Offset Y [mm]
+00.00
+00.00
Offset Z
Fig. 3B92
+00°00′
Offset H
Fig. 3B93
+0.00
(C02_02) Unit P.C.B. B.B.R.
Select one of the following options to determine whether or
not the unit P.C.B. B.B.R. function should be used.
Disable : The unit P.C.B. B.B.R. function is not used.
Enable : The unit P.C.B. B.B.R. function (2-point rec-
ognition) is used.
• When "Enable" is set, the recognition coordinate differ as
shown below in (1) according to the parameter set in the
"P.E.C. recognition mode image" text box (described in
"(A02_01) P.E.C. recognition function"). Refer to "(A02)
P.E.C. Recognition Data" in "2.3 Operation Data".
Options for Image Recognition Mode
(1) The following is based on the parameter "Enable" (Nor-
mal Image Recognition Mode).
Fig. 3B95 Example of Unit P.C.B. B.B.R. Recognition
(a) Refer to "2. Various Functions" (Section 2) in "Vol. 2: Op-
eration (Supervisor)" for details.
(b) The pattern origin (coordinates) must be located inside the
placement coordinate reference point (coordinates).
(c) Determine the coordinates of the first and second fiducial
marks for the unit P.C.B. B.B.R. recognition function.
2.5 Placement Data
Unit P.C.B. B.B.R.
Fig. 3B94
Disable
0206-002 2-48 AHB01EDTP