3OM-1075-002.pdf - 第76页

(C03) Placement Data (O) The set parameters can be used to create a repetitive pat- tern program. Fig. 3B1 16 Edit Window (Example) (C03_01) O-No. Shown are the step Nos. of the placement data (O). These step Nos. are re…

100%1 / 357
(C02_13) V
Select one of the following options as the data for the local
recognition mode.
00 : The P.E.C. recognition is not performed.
01 : The P.E.C. recognition is performed. (1-Point Rec-
ognition)
02 : The P.E.C. recognition is performed. (2-Point Rec-
ognition)
Set a parameter in this text box after specifying "Enable" in
the "P.E.C. recognition function" and "P.E.C. recognition
mode Local" text boxes in the "P.E.C. Recognition Data" tab
sheet (Operation Data).
(C02_14) X1 [mm], Y1 [mm]
Set the coordinates of the first fiducial mark for the local
P.E.C. recognition.
The coordinates must be based on the pattern origin
when a P.C.B. has repetitive patterns.
(C02_15) X2 [mm], Y2 [mm]
Set the coordinates of the second fiducial mark for the
local P.E.C. recognition.
The coordinates must be based on the pattern origin
when a P.C.B. has repetitive patterns.
(C02_16) FM1, FM2
Set the mark Nos. of the first and second fiducial marks
FM1 and FM2 for local P.E.C. recognition.
Select the mark Nos. (Mark #) specified in the P.C.B. recog-
nition mark data of the operation data.
0206-002 2-56
AHB01EDTP
2.5 Placement Data
Fig. 3B115
FM1 [mm]
00
FM2 [mm]
00
Fig. 3B114
X2 [mm]
000.000
Y2 [mm]
000.000
Fig. 3B113
X1 [mm]
000.000
Y1 [mm]
000.000
V
Fig. 3B112
00
(C03) Placement Data (O)
The set parameters can be used to create a repetitive pat-
tern program.
Fig. 3B116 Edit Window (Example)
(C03_01) O-No.
Shown are the step Nos. of the placement data (O).
These step Nos. are regarded as repetitive pattern Nos.
Parameters must be entered in each line (pattern).
Fig. 3B118 Example of Repetitive Pattern Program
0206-003 2-57
AHB01EDTP
2.5 Placement Data
0-No.
Fig. 3B117
1
(C03_02) X [mm], Y [mm]
Set the coordinates of each pattern origin (O
01
through O
n
)
based on the placement coordinate reference point (N
0
).
Unit: mm
A pattern origin refers to the reference coordinates of a re-
petitive pattern.
The pattern origins (reference coordinates) must be deter-
mined, regarding the "Z-theta" data as "0°" (described in
"(C03_03)" and located at corners on the same side as the
placement coordinate reference point (N
0
).
N
0
: The center of is the placement coordinate refer-
ence.
O
01
: Pattern Origin of Pattern 1
O
02
: Pattern Origin of Pattern 2
O
03
: Pattern Origin of Pattern 3
O
04
: Pattern Origin of Pattern 4
Fig. 3B120 Example of Repetitive Patterns
Do not set any coordinates in the last line (last step No.).
Keep them as "000.00".
0206-003 2-58
AHB01EDTP
2.5 Placement Data
Fig. 3B119
X [mm]
010.000
Y [mm]
010.000