operation-cp45.pdf - 第79页
Basic Configuration and Name of Each Part 2-27 2.13.2. General nozzles Nozzles should be properly selected according to the type and size of the components. The nozzles generally used in the CP-45F V model are identical.…
Samsung Component Placer CP-45F(V)/FS Operations Manual
2-26
reduced even when ANC is ed.
2.13. Nozzle
2.13.1. Nozzle types
Nozzles are largely divided into general nozzles and special nozzles (nozzles for non-
standard components).
General nozzles
Applicable to all generally used components. These components include chips, SOJ,
SOP, PLCC, QFP, etc.
Special nozzles
Nozzles for non-standard components
These are for non-standard components of various shapes such as connectors,
sockets, etc. Components with odd shapes can be manufactured and applied.
Among nozzles for non-standard components, the diffuser type nozzles (TP20,
TP40) are for improving visibility of the components requiring for vision
treatment.
Caution
Operating the shutter while a finger is inserted in the
ANC could result in severe injury. Do not insert a finger
into the ANC Hole.
Basic Configuration and Name of Each Part
2-27
2.13.2. General nozzles
Nozzles should be properly selected according to the type and size of the components.
The nozzles generally used in the CP-45FV model are identical. Black nozzles are
occasionally used for some components in the flying vision unit and the upward vision
unit.
The nozzle should be selected correctly since it may cause improper adsorption, or
improper placement problems. The nozzles generally used are shown in “Table 2-7“. For
accurate pick & place, a proper nozzle should be selected in reference to the minimum
suction area of each component.
Table 2-7. General Nozzles
Nozzle name
TN-03 TN-04 TN-065 TN-14 TN-22 TN-40 TN-75 TN-110
Outer diameter
Φ 0.8 Φ 0.75 Φ 1.2 Φ 2.2 Φ 3.6 Φ 6.2 Φ 9.0 Φ 12.7
Inner diameter
Φ 0.28 Φ 0.38 Φ 0.65 Φ 1.4 Φ 2.2 Φ 4.0 Φ 7.5 Φ 11.0
Table 2-8. Examples of Applying General Nozzles to Components
Nozzle
name
Minimum
component
width
Major component types
TN-03 0.3 ~ 1.5 0603,1005 only
TN-04 0.5 ~ 1.25 1005, 1608, 2012,3216, SOT(Molded part 0.8 X 1.6)
TN-065 0.8 ~ 2.5 1608, 2012,3216, MELF(Molded part 1.2 X 2.0), SOT23
TN-14 2.5 ~ 4.0
Aluminum electrolytic capacitor(small), Tantalum capacitor,
Trimmer
TN-22 4.0 ~ 7.0
Aluminum electrolytic capacitor(medium), SOP(Narrow), SOJ,
Connector
TN-40 7.0 ~ 10.0
Aluminum electrolytic capacitor(large), SOP(Wide), TSOP, QFP,
PLCC, SOJ, Connector
TN-75 10.0 ~ QFP(medium), PLCC(medium)
TN-110 20.0 ~ QFP(large), PLCC(large)
Our company can supply various nozzle types are not included in “Table 2-7“ to satisfy
the user requirement. For inquiries on special nozzles, please contact our Business
Department or C/S Center.
Memo
Samsung Component Placer CP-45F(V)/FS Operations Manual
2-28
2.13.3. Special nozzles
Table 2-9. Special Nozzles
Type Odd(for Odd-type components) Calibration Tool
Nozzle Name TP20 TP40 CN20
Inner Diameter - -
ψ 2.0
Outer Diameter - -
ψ 15.4
Pickup Area
2× 10 4× 12
ANC hole Large Large Large
Table 2-10. Examples of Applying Special Nozzles to Components
Nozzle
name
Minimum
component
width
Major component types
TP20 2.5 ~ Connectors for which vacuum adsorption is possible
TP40 4.5 ~ Connectors for which vacuum adsorption is possible
CN20 - Tool for Calibration
Caution
This table simply means that the conventional nozzle of 10-
hole ANC has the same inner and outer diameters as those of
the nozzle of 20-hole ANC. It does not mean that they can be
used interchangeably. Only nozzles listed in the above table
should be used for each ANC type.
Caution
The machine might operate irregularly if standard regular
nozzles are not used.
1. Failure of nozzle change
2. Dislocation of nozzle during operation
3. Failure of component pick up
Be sure to use standard regular nozzles.