CM602all_EJM8AESM_Service Manual.pdf - 第1051页
Another parameter 2 Name PF18 For manufacturer setting PF19 For manufacturer setting PF20 For manufacturer setting Another parameter 3 Name For manufacturer setting For manufacturer setting For manufacturer setting For m…
Another parameter 1
Name
PE07 For manufacturer setting 100 100
PE08 For manufacturer setting 10 10
PE09 For manufacturer setting 0 0
PE10 For manufacturer setting 0 0
PE11 For manufacturer setting 0 0
PE12 For manufacturer setting 40 40
PE13 For manufacturer setting FFFE FFFE
PE14 For manufacturer setting 111 111
PE15 For manufacturer setting 20 20
PE16 For manufacturer setting 0 0
PE17 For manufacturer setting 0 0
PE18 For manufacturer setting 0 0
PE19 For manufacturer setting 0 0
PE20 For manufacturer setting 0 0
PE21 For manufacturer setting 0 0
PE22 For manufacturer setting 0 0
PE23 For manufacturer setting 0 0
PE24 For manufacturer setting 0 0
PE25 For manufacturer setting 0 0
PE26 For manufacturer setting 0 0
PE27 For manufacturer setting 0 0
PE28 For manufacturer setting 0 0
PE29 For manufacturer setting 0 0
PE30 For manufacturer setting 0 0
PE31 For manufacturer setting 0 0
PE32 For manufacturer setting 0 0
PE33 For manufacturer setting 0 0
PE34 For manufacturer setting 0 0
PE35 For manufacturer setting 0 0
PE36 For manufacturer setting 0 0
PE37 For manufacturer setting 0 0
PE38 For manufacturer setting 0 0
PE39 For manufacturer setting 0 0
PE40 For manufacturer setting 0 0
Another parameter
2
Name
PF01 Function selection F-1
PF02 Function selection F-2
PF03 Function selection F-3
PF04 RS-422 communication time-out selection
PF05 USB communication time-out selection
PF06 Function selection F-4(Non-supported)
PF07
Non-limited len
g
th absolute position electronic
g
ear numerator
(
No. of machine teeth
)(
Non-supporte
d
PF08 Non-limited len
g
th absolute position electronic
g
ear denominator
(
No. of motor tooth
)
(
Non-supporte
d
PF09 Function selection F-5
PF10 Function selection F-6
PF11 Function selection F-7
PF12 Speed limit (Non-supported)
PF13 Restore motion speed (Non-supported)
PF14 Restore motion acceleration time constant (Non-supported)
PF15 Software dynamic brake motion time (Non-supported)
PF16 Function selection F-8
PF17 Origin set error detection time
TL-axis TP-axis
0
0
0
TL-axis TP-axis
Lift-axis (TL) and Extension-axis (TP) Parameter List
No.
No.
0
Tray Direct Tray
0
0
0
00
10 10
100
100
2000
0
0
1
1
1
1
0
0
10000
0
0
100
100
2000
0
1
1
0
0
10000
EJM8A-E-SMA070209-A01-00
Page 7-2-9-10
Another parameter
2
Name
PF18 For manufacturer setting
PF19 For manufacturer setting
PF20 For manufacturer setting
Another parameter
3
Name
For manufacturer setting
For manufacturer setting
For manufacturer setting
For manufacturer setting
For manufacturer setting
TL-axis TP-axis
Direct Tray
Lift-axis (TL) and Extension-axis (TP) Parameter List
No.
PO04
PO05
PO06
PO07
TL-axis
0
Tray
PO01
PO02
For manufacturer setting
0
0
0
No.
PO03
0
0
0
0
PO08
Option card mount detection
For manufacturer setting
0
0
0
0
0
0
0
0
0
0
TP-axis
0
0
0
0
EJM8A-E-SMA070209-A01-00
Page 7-2-9-11
Jig: FM-1924
Pulley-holding jig
Tension gauge
Phillip screwdriver #2
Allen key 2 mm
Allen key 3 mm
Allen key 4 mm
Pulley remover
Tension gauge
Torque wrench
Teaching
Direct Tray
• This section describes the procedures for replacing the extension-axis motor.
7-2-10 Extension-axis Motor Replacement
Min.
30
Removal/Disassembly
20
Min.
kgs.
80
Part Weight
Assembly/Adjustment
Min.
Total
Min.
30
Tray
Tool
Jig
Caution
Danger
Warning
EJM8A-E-SMA070210-A01-00
Page 7-2-10-1