CM602all_EJM8AESM_Service Manual.pdf - 第835页
Remark Component-Thickness-Measuring Unit Item Option Part and Accessory Replacement Close the amplifier cover. 15 Light-axis adjustment (Preparation 1) 1. Adjust the gap between the block A and the plate B,using the adj…
Remark
Component-Thickness-Measuring Unit
Item
Option Part and Accessory Replacement
Install the sensor.
1.Insert the plate (D) into the sensor (C)
that has the M6 nut (1). Screw the slit
(A) fully. Unscrew the slit slightly until
the sensor is positioned with its
indication upwards, and the R-shaped
section of the slit is positioned in the
specified position. Fix the sensor with
M6 nut (1).
2. Put a new bushing (2) first. Half
tighten the Hexagon-socket-head
setscrew (3).
<Caution.>
1. Light-emitting: Indication in red
Light-sensing : Indication in blue
2. Slits are different between light-
emitting and -sensing sides. (See
pictures)
3. For the position of the R-shaped
section of the slit, see the pictures.
(1) M6 nut
(2) Bushing
(3) Hexagon-socket-head
setscrew M3 x 4L
A: Slit (light-emitting)
B: Slit (light-sensing)
C: Sensor
D: Plate
Allen key M2
Wrench 10 mm
Wrench 12 mm
13
Close the connector lock.
14
12
Insert the sensor cables into the amplifier connector lock.
R-shaped
Light-sensing
Light-emitting
C B1
2 3
D
D
C
1
3
2
A
R-shaped
Large slit: light-emittingSmall slit: light-sensing
Insert the sensor cables into
the amplifier connector lock.
Close the
connector lock.
EJM8A-E-SMA060405-A01-00
Page 6-4-5-5
Remark
Component-Thickness-Measuring Unit
Item
Option Part and Accessory Replacement
Close the amplifier cover.
15
Light-axis adjustment (Preparation 1)
1. Adjust the gap between the block A
and the plate B,using the adjusting bolts
(1) until the gap becomes 0.
2. Keeping the gap 0, press the block
gauge (10 mm) against the reference
surfaces of the block A and the block B.
Level the block A and the plate B by
aligning them with the block gauge. Fix
them by tightening the adjusting bolts
(1).
<Caution>
Basically it is not necessary to position
the light-sensing plate.
(1) M4 x 16L (2 pcs.)
A: Block
B: Plate
Block gauge (10 mm)
Light-axis adjustment (Preparation 2)
Fix the (2. component-thickness-
measuring-unit-light-axis-adjusting jig) in
place with the bolt (1).
(1) M4 x 16L
FM-1962(2)
(2. Component-thickness-
measuring-unit-light-axis-
adjusting jig)
16
17
A
1
FM-1962(2)
Component-thickness-measuring-unit-
light-axis-adjusting jig
Close the amplifier cover.
1
B
Block gauge
Gap
EJM8A-E-SMA060405-A01-00
Page 6-4-5-6
Remark
Component-Thickness-Measuring Unit
Item
Option Part and Accessory Replacement
FM-1962(1)
(1. Component-height-
detection-sensor-
adjusting-power box)
Loosen the M4 bolts (1). Moving the light-
emitting-axis horizontally, align the laser light
with the center of the horizontal slit of the
FM-1962 (2) (2. component-thickness-
measuring-unit-light-axis-adjusting jig).
Tighten the M4 bolts (1).
Bolt M4
M4 x 16L (2 pcs.)
FM-1962(2)
(2. component-thickness-
measuring-unit-light-axis-
adjusting jig)
Loosen the M6 nut (1). Turn the light-
emitting-axis eccentric pin to align the
laser light with the center of the vertical
slit of the FM-1962 (2) (2. Component-
thickness-measuring-unit-optical-axis-
adjusting jig). Find a position at which
the amplifier value (light-sensing
amount) is 2000 or more. Tighten the
M6 nut.
If the laser light is positioned far from
the vertical slit in the vertical direction,
loosen the bolt (3) and align the light-
axis with the groove.
Nut M6
FM-1962(2)
(2. component-thickness-
measuring-unit-optical-
axis-adjusting jig)
18
19
20
Connect the power box (24VDC) to the amplifier.
Adjust the light-emitting light-axis in the horizontal direction.
Adjust the light-emitting light-axis in the vertical direction.
Laser light
1
Horizontal slit
1
2
3
2000 or more
Slit
Laser light
EJM8A-E-SMA060405-A01-00
Page 6-4-5-7