CP643 系统参考.pdf - 第103页
1.7.3 Carrying Out Device Check When device check is carried out the following operation screen displays. The meaning of each item that displays is explained below. A: Device number B: Status of parts Un Set (yellow) : D…
1.7.2 Setting Proper Data
To carry out device check it is necessary to set the following Proper data items.
70: Device Check SW No : Parts : Miss : Error
This item determines whether or not a mandatory device check will be performed when
parts run out and when a program change has occurred.
No : Mandatory device check is not performed.
Parts : Mandatory device check is performed when parts run out.
Miss : Mandatory device check is performed when parts run out or when parts
are mispicked.
Error : Mandatory device check is performed when parts run out, parts are
mispicked or a vision processing error occurs.
71: Verifier Tool Non : Barcode : Handy_term
This item specifies the hardware to be used in device check.
Non : Handy terminal is not used.
Barcode : Not supported
Handy_term : Handy terminal is used (option)
Caution: If "Handy_term" is set then a value other than 0 must be set in Proper data item 72:
Barcode Reader Type.
74: ESC Permission Non : Permit
This item determines whether or not the [ESC] command will be enabled during device
check. The [ESC] command allows the user to set all parts that are "Un Set" (any parts
that are not “Set OK”).
Non : [ESC] command is disabled.
Permit : [ESC] command is enabled.
75: MAN Permission Non : Permit
This item determines whether or not it is possible to input data from the handy terminal
numerical keypad to the operation panel on the machine.
Non : Numerical keypad is disabled.
Permit : Numerical keypad is enabled.
If this item is set to "Permit" the numerical keypad and CR key on the operation panel
are also enabled.
Part 2 Chapter 1 Basic Operation
Edition 1.1 2-1-45 CP643E System Reference
1.7.3 Carrying Out Device Check
When device check is carried out the following operation screen displays. The meaning
of each item that displays is explained below.
A: Device number
B: Status of parts
Un Set (yellow) : Device has not yet been checked
OK (green) : Device has been set
(blue) : Device was used in previous program but is not going to be
used in the coming program.
Next D : Next device is not yet set
Tape E (white) : End of tape detected
Parts E (red) : Feeder is out of parts
Pickup : Parts mispicked
(highlighted in yellow)
Vision (purple) : Vision processing error
C: Number of parts used per board
D: Device comment
+PAGE -PAGE ▲▼ESC
CP643S2029
RETURN
D001
D002
D003
D004
D005
D006
D007
D008
D009
D010
D015
Un Set
Parts E
Vision
Tape E
Next_D
Pickup
[0013]
[0008]
[0002]
[0000]
[0001]
[0005]
[0007]
[0002]
[0003]
[0015]
[0023]
Device_comment_No1
Korewa_No_2_Desu
PCPR102TL
MSD2HD256
Micro_TR_No1
Super_Mini_TR
Nihongonetute
N3456Sd23
Jaf
RECT3216060
Page 451
Unset
AB C D
Part 2 Chapter 1 Basic Operation
Edition 1.1 2-1-46 CP643E System Reference
As shown in the above figure there are 3 types of display modes for device check.
F1: MODE 1
In this mode the display screen will be the same as the one in the figure above where 10
consecutive device positions display whether the device position is used or not.
F2: MODE 2
In this mode the screen display will be like the one below where only the device
positions that are used in the program actually appear on the screen.
F3: MODE 3
In this mode the display screen will be like the one shown below. Among the device
positions that are used in the program, only those positions with a status condition such
as Un Set, Parts E, Pickup, Vision, etc. will actually display on the screen.
+PAGE -PAGE ▲▼ESC
CP643S2030
RETURN
D001
D002
D005
D006
D007
D009
D015
Un Set
Parts E
Vision
Tape E
Next_D
Pickup
Unset
[0013]
[0008]
[0001]
[0005]
[0007]
[0003]
[0023]
Device_comment_No1
Korewa_No_2_Desu
MSD2HD256
Micro_TR_No1
Super_Mini_TR
N3456Sd23
RECT3216060
Page 451
+PAGE -PAGE ▲▼ESC
RETURN
D001
D002
D003
D004
D005
D006
D007
D008
D009
D010
D015
Un Set
Parts E
Vision
Tape E
Next_D
Pickup
[0013]
[0008]
[0002]
[0000]
[0001]
[0005]
[0007]
[0002]
[0003]
[0015]
[0023]
Device_comment_No1
Korewa_No_2_Desu
PCPR102TL
MSD2HD256
Micro_TR_No1
Super_Mini_TR
Nihongonetute
N3456Sd23
Jaf
RECT3216060
Page 451
Unset
AB C D
Part 2 Chapter 1 Basic Operation
Edition 1.1 2-1-47 CP643E System Reference