CP643 系统参考.pdf - 第70页

5. Transmit status data to the machine. Status data is retained in the machine’s memory even after the machine’s power is turned off. Thus, once status data has been transmitted to the machine, this step need not be repe…

1.2 Getting Started

1.2.1 Starting the Machine

This section explains everyday start-up, reset-start and I/O check start procedures.

Normal Operation

Use the following procedure to start the machine.

1. Boot up the host computer.

This computer compiles production information transmitted from the machine in Off

Line mode.

2. Set the circuit breaker.

The machine’s main circuit breaker must be set to the ON position before the machine

can be turned on.

3. EMERGENCY STOP button check

Verify that the EMERGENCY STOP button has been pressed.

4. Turn on the power.

Press the POWER ON button on the machine operation panel to turn the machine on.

After pressing the POWER ON button, make sure that the display appears as

follows:

Page 000

Off line

MachineNot Zero-Set

Press START

CP_6.PROGRAM Prod 00000 Sche 00000

v1.10

000000000000

jog X Y C

AUTO STEP LOADER PROGRAM SET

CP643S2006

✽

READY

LOADER

ST 1. N

ST 2. N

ST 3. N

ST 6. N

ST 7. N

ST 8. N

ST 10. N

ST 11. N

1Er****

1Er 0

STATUS

P Mode

Recovery

T Mode

Product

3 times

Joint

Part 2 Chapter 1 Basic Operation

Edition 1.1 2-1-12 CP643E System Reference

5. Transmit status data to the machine.

Status data is retained in the machine’s memory even after the machine’s power is

turned off. Thus, once status data has been transmitted to the machine, this step need

not be repeated. However, it is necessary to transmit status data to the machine after

performing the reset-start procedure. Status data can be modified either directly at

the machine, or indirectly using an host computer. When status data is modified

using the host computer, it must be transmitted to the machine before operation.

6. Transmit Proper data to the machine.

Proper data is retained in the machine’s memory even after the machine’s power is

turned off. Once Proper data has been transmitted to the machine, this step need not

be repeated. However, it is necessary to transmit Proper data to the machine after

performing the reset-start procedure. When Proper data is modified at the host

computer, the modified Proper data must then be transmitted to the machine before

operation. It is also possible to change a part of Proper data at the machine. If the

Proper data is transmitted to the host computer once the change is made at the

machine, then that Proper data will be saved at the host computer.

7. Transmit programs to the machine.

Programs are retained in the machine’s memory even after the machine’s power is

turned off. Once a program has been transmitted to the machine, this step need not

be repeated. However, it is necessary to transmit programs to the machine after

performing the reset-start procedure. New programs can be created using the host

computer. These must be transmitted to the machine before they can be used in

production.

8. EMERGENCY STOP button cancel

Release the EMERGENCY STOP button, then press the RESET button.

9. Select the production program.

Using either host computer or the machine [PROGRAM] command function, select

the production program.

10. Select the quantity of the production run.

Press the [PROGRAM], [QTY SET] command function keys and set the number of

boards to be produced. A setting of zero will make the machine run indefinitely.

Note: Scheduled production quantity can be set in the program. Enter the production quantity

into the Production_qty. field (in the Production_mode section at MCS), and transmit to

the machine. When the production run is complete the machine will stop and the

operator will be informed. (This function is used only in MCS systems. F4G systems

do not have this function.)

11. Zero-setting

The START button flashes and a “Machine Not Zero Set” message displays on-

screen. Press START to begin the zero-setting operation.

12. Commands

The F1 to F6 function keys can be used to execute commands.

Note: Some of these commands are disabled during vision processing (when a “Vision

System Booting...” message displays). In such cases, wait until vision processing is

completed before using those commands.

Part 2 Chapter 1 Basic Operation

Edition 1.1 2-1-13 CP643E System Reference

13. Set the operation mode.

In either [AUTO] or [STEP], press the [MODE] command to access the following

three modes of operation.

• F1 : Product

Carries out normal production of boards.

• F2 : Simulate

The XY-table and the device tables operate as they do during production, however

boards are not loaded.

• F3 : Idle

Machine carries out all functions except vision processing and fiducial mark reading.

The loader is inoperative at this time, and boards are not exchanged.

• F4 : Idle 2

In addition to the previous “Idle” function, IN/OUT carrier operation and board transfer

operation between the XY-table and the carriers are performed. Board exchanges do not

occur.

Caution: The operation mode “Product” is automatically selected when the power supply is turned

on. Operation modes “Simulate,” “Idle” and “Idle 2” are not for assembly.

Part 2 Chapter 1 Basic Operation

Edition 1.1 2-1-14 CP643E System Reference