CP643 系统参考.pdf - 第252页
SET 532-2-1/2-5 Command Pass: [SET] - [PROPER] - [X/Y] - [PCB LD / UNLD] - [UNLOAD POS.] / [LOAD POS.] - [SET] This command sets the value in the relevant Proper data item. Second display area When the start conditions a…
PCB LD / UNLD 532-2-0
Command Pass: [SET] - [PROPER] - [X/Y] - [PCB LD / UNLD]
This is used to set the XL_OUT/YL_OUT or XL_IN/YL_IN measurement results in Proper data.
Revision History
V1.10 and later
UNLOAD POS. 532-2-1
Command Pass: [SET] - [PROPER] - [X/Y] - [PCB LD / UNLD] - [UNLOAD POS.]
This is used to set the XL_OUT/YL_OUT measurement results in Proper data.
Revision History
V1.10 and later
LOAD POS. 532-2-2
Command Pass: [SET] - [PROPER] - [X/Y] - [PCB LD / UNLD] - [LOAD POS.]
This is used to set the XL_IN/YL_IN measurement results in Proper data.
Revision History
V1.10 and later
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-91 CP643E System Reference
SET 532-2-1/2-5
Command Pass: [SET] - [PROPER] - [X/Y] - [PCB LD / UNLD] - [UNLOAD POS.] / [LOAD POS.]
- [SET]
This command sets the value in the relevant Proper data item.
Second display area
When the start conditions are satisfied, the message “Set Proper.” will flash in green in this display
area. In all other cases an error will display.
First status area
Either “UNLOAD POS.” or “LOAD POS.” will display, whichever is relevant.
Revision History
V1.10 and later
XPCB/YPCB 532-3-0
Command Pass: [SET] - [PROPER] - [X/Y] - [XPCB/YPCB]
Press to set the XPCB/YPCB calibration results into Proper data.
Revision History
Xmax/Ymax 532-4-0
Command Pass: [SET] - [PROPER] - [X/Y] - [Xmax/Ymax]
Press to set the Xmax/Ymax calibration results into Proper data.
Revision History
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-92 CP643E System Reference
Xmin/Ymin 532-5-0
Command Pass: [SET] - [PROPER] - [X/Y] - [Xmin/Ymin]
Press to set the Xmin/Ymin calibration results into Proper data.
Revision History
SET 532-1/3/4/5-1
Command Pass: [SET] - [PROPER] - [X/Y]
- [X0/Y0]/[XPCB/YPCB]/[Xmax/Ymax]/[Xmin/Ymin] - [SET]
Press to set the relevant Proper data.
Second Display Area
If start conditions are fulfilled, the message “Press START” flashes. Otherwise an error displays.
First Status Area
The relevant X0/Y0, XPCB/YPCB, Xmax/Ymax and Xmin/Ymin values are displayed here.
Revision History
V1.10 and later
D1/D2 533-0-0
Command Pass: [SET] - [PROPER] - [D1/D2]
Press to set Proper data for the D1- and D2-axes.
Revision History
V1.10 and later
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-93 CP643E System Reference