CP643 系统参考.pdf - 第196页
-P AGE 455-2-0 Command Pass: [PROGRAM] - [DEVICE] - [OFFSET] - [-PAGE] Press to display the previous page. Revision History ▲ 455-3-0 Command Pass: [PROGRAM] - [DEVICE] - [OFFSET] - [ ▲ ] Press to move the cursor up one …
OFFSET 455-0-0
Command Pass: [PROGRAM] - [DEVICE] - [OFFSET]
Press to set device offset for any device in the current program.
First Display Area
[Example]
DEVICE OFFSET Editor
D No. Proper DATA Part DATA Auto Rev.
D001 00.000 [mm] 00.0 [mm] 00.000 [mm]
D002 00.000 [mm] 00.0 [mm] 00.000 [mm]
D003 00.000 [mm] 00.0 [mm] 00.000 [mm]
D004 00.000 [mm] **** [mm] ****** [mm]
D005 00.000 [mm] **** [mm] ****** [mm]
D006 00.000 [mm] 00.0 [mm] 00.000 [mm]
D007 00.000 [mm] 00.0 [mm 00.000 [mm]
D008 00.000 [mm] 00.0 [mm] 00.000 [mm]
D009 00.000 [mm] **** [mm] ****** [mm]
D010 00.000 [mm] **** [mm] ****** [mm]
No.: Device number
Proper Data: The Proper data settings for Device Offset 1 ~ Device Offset 140 are displayed here.
These settings can be entered directly at the machine.
Part Data: The Part data settings in Pickup_offset are displayed here. The asterisks (******)
indicate that the device is not being used. These settings cannot be entered directly
at the machine.
Auto Rev.: The amount of automatic offset is displayed here. The asterisks (******) indicate that
the device is not being used. These settings cannot be entered directly at the
machine.
Revision History
+PAGE 455-1-0
Command Pass: [PROGRAM] - [DEVICE] - [OFFSET] - [+PAGE]
Press to display the next page.
Revision History
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-35 CP643E System Reference
-PAGE 455-2-0
Command Pass: [PROGRAM] - [DEVICE] - [OFFSET] - [-PAGE]
Press to display the previous page.
Revision History
▲ 455-3-0
Command Pass: [PROGRAM] - [DEVICE] - [OFFSET] - [▲]
Press to move the cursor up one line.
Revision History
▼ 455-4-0
Command Pass: [PROGRAM] - [DEVICE] - [OFFSET] - [▼]
Press to move the cursor down one line.
Revision History
DATA INPUT 455-5-0
Command Pass : [PROGRAM] - [DEVICE] - [OFFSET] - [DATA INPUT]
Press this key after selecting the device number. Enter offset values in Proper Data from the
numerical keypad in units of 1/1000 mm.
[Example]
If 0.1 mm is the desired offset value then input “100” from the numeric keypad.
Revision History
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-36 CP643E System Reference
SET 500-0-0
Command Pass : [SET]
Press to make other settings.
Revision History
STATUS 510-0-0
Command Pass : [SET] - [STATUS]
Press to change the machine status.
Revision History
RECOVERY 511-0-0
Command Pass : [SET] - [STATUS] - [RECOVERY]
Press to select the recovery mode.
Revision History
RECOV. NUMER 511-1-0
Command Pass : [SET] - [STATUS] - [RECOVERY] - [RECOV. NUMER]
Enter any number from 1 to 9 to set the number of recovery attempts.
Revision History
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-37 CP643E System Reference