CP643 系统参考.pdf - 第239页
+NOZZLE 523-1-5-1/2-2-3 Command Pass: [SET] - [MANUAL] - [NOZZLE] - [CENTER] - [DISPLAY] - [WIDE]/[NARROW] - [BACKLIGHT DATA] - [+NOZZLE] Press to increase the nozzle number of the results being displayed by one. The noz…
BACKLIGHT DATA 523-1-5-1/2-2
Command Pass: [SET] - [MANUAL] - [NOZZLE] - [CENTER] - [DISPLAY]
- [WIDE]/[NARROW] - [BACKLIGHT DATA]
Display nozzle back light measurement results.
Caution: The data displayed on the screen is the nozzle type data selected using the command. The
nozzle type display also changes accordingly.
When this screen is first opened (default), the No. 1 nozzle data is displayed.
The camera type selected using the higher order command will display in yellow.
In each data display, the value will display in white if it is within the tolerance range and in red if
it is not within the tolerance. In addition, for nozzles with a measurement error instead of a
value being displayed, “∗∗∗” will display in yellow.
Revision History
PAGE 523-1-5-1/2-2-1
Command Pass: [SET] - [MANUAL] - [NOZZLE] - [CENTER] - [DISPLAY]
- [WIDE]/[NARROW] - [BACKLIGHT DATA] - [PAGE]
The display toggles between the measurement results for nozzle heads A ~ J and K ~ T.
Revision History
CP643S3023
BACK LIGHT CONDITION
NOZZLE: 1
CAMERA: WIDE VIEW
Head
A
B
C
D
E
Gray
176
***
193
201
169
Dev
16
***
25
16
23
STANDARD VALUE
STANDARD DEV
Head
F
G
H
I
J
Gray
***
183
189
191
179
Dev
***
27
18
20
19
: 170 (± 20)
: 0 (+ 3)
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-78 CP643E System Reference
+NOZZLE 523-1-5-1/2-2-3
Command Pass: [SET] - [MANUAL] - [NOZZLE] - [CENTER] - [DISPLAY]
- [WIDE]/[NARROW] - [BACKLIGHT DATA] - [+NOZZLE]
Press to increase the nozzle number of the results being displayed by one. The nozzle following
nozzle 6 is nozzle 1.
Revision History
-NOZZLE 523-1-5-1/2-2-4
Command Pass: [SET] - [MANUAL] - [NOZZLE] - [CENTER] - [DISPLAY]
- [WIDE] / [NARROW] - [BACKLIGHT DATA] - [-NOZZLE]
Press to decrease the nozzle number of the results being displayed by one. The nozzle following
nozzle 1 is nozzle 6.
Revision History
NOZZLE SKIP 523-2-0
Command Pass: [SET] - [MANUAL] - [NOZZLE] - [NOZZLE SKIP]
Enables nozzles to be skipped manually.
Revision History
NOZZLE TYPE 523-2-1
Command Pass: [SET] - [MANUAL] - [NOZZLE] - [SKIP NOZZLE] - [NOZZLE TYPE]
Press to choose from nozzle 1~6.
Revision History
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-79 CP643E System Reference
▲ 523-2-3
Command Pass: [SET] - [MANUAL] - [NOZZLE] - [SKIP NOZZLE] - [▲]
Press to move the cursor up one line.
Revision History
▼ 523-2-4
Command Pass: [SET] - [MANUAL] - [NOZZLE] - [SKIP NOZZLE] - [▼]
Press to move the cursor down one line.
Revision History
SKIP/CLEAR 523-2-5
Command Pass: [SET] - [MANUAL] - [NOZZLE] - [SKIP NOZZLE] - [SKIP/CLEAR]
Align the cursor with the desired nozzle and press this key to manually set the nozzle to be
skipped. "SKIP" will display in yellow beside the nozzle. Use the same key to cancel the skip
setting. When the cursor is set at a nozzle which has been set to be skipped, the command will
change to “CLEAR”.
Revision History
HT (Displayed for Handy Terminal) 524-0-0
Command Pass: [SET] - [MANUAL] - [HT]
Press to enter commands related to the Handy Terminal.
An ID code is necessary for entering this command. This command will not appear if the Handy
Terminal option is not used.
Revision History
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-80 CP643E System Reference