CP643 系统参考.pdf - 第74页

1.2.4 Reset-Start The contents of the machine’s memory have to be cleared whenever the machine’s memory card and ROM chips are replaced to upgrade the software. It may also be necessary to clear the memory of erroneous d…

Zero-setting of all the 9 axes of the machine are performed at the same time. During

zero-setting a display like the one shown below will appear in the second display area.

After zero-setting is complete, the D1 and D2 axes tables will move to their respective

resupply positions and the shutters will then lower.

1.2.3 Shutting Down

When shutting down the power, use the following procedure.

1. Turn off the 200V power.

Press the EMERGENCY STOP button. When shutting down in the course of

production, first press the CYCLE STOP button to halt automatic operation before

pressing the EMERGENCY STOP button.

2. Turn off the main power.

Press the POWER OFF button on the operation panel to turn off the power supply.

3. Turn off the circuit breaker.

Turn off the power at the main circuit breaker if the machine is to be left unused for a

long period of time or if work is to be carried out on the servo box or control box.

Caution:

• If the power is cut while parts are being picked, the parts will drop off the nozzles, and

during the next production run, vision processing may not work properly if parts have fallen

onto the prism box. To prevent this, execute the following command sequence before

cutting the power in order to discard parts which have been picked up:

[Set] - [POSITION] - [DUMP PARTS] - [START]

• Feeder changes are not possible if the power is shut off when the device table is near the

pick-up position. Moreover, when the power is turned on again, it will take longer to zero

set the machine. Therefore, the following command sequence should be executed to move

the device table to its retract position before shutting the power off:

[SET] - [POSITION] - [D RESUPPLY] - [TABLE 1/2] - [START]

CP643S2009

Zero Set

CP643S2008

Part 2 Chapter 1 Basic Operation

Edition 1.1 2-1-16 CP643E System Reference

1.2.4 Reset-Start

The contents of the machine’s memory have to be cleared whenever the machine’s

memory card and ROM chips are replaced to upgrade the software. It may also be

necessary to clear the memory of erroneous data when the machine begin to operate

abnormally.

All status data, Proper data and production programs are deleted from the memory of

the machine when the reset-start operation is carried out. Therefore, these data have to

be transmitted from the host computer to the machine again. Remember to restart the

machine after transmitting the Proper data from the computer.

Use the following procedure to reset-start the machine.

1. Boot-up the host computer.

This computer compiles production information transmitted from the machine in Off

Line mode.

2. Set the circuit breaker.

The machine’s main circuit breaker must be set to the ON position before the machine

can be turned on.

3. Turn on the power.

While pressing the RESET button, press the POWER ON button. When “Memory

Backup NG” appears on the display screen the RESET button may be released.

4. 200V ON.

Release the EMERGENCY STOP button if it has been pressed in.

5. Transmit the status data.

Transmit the correct status data from the host computer.

Note: For information concerning the meaning of status data values, refer to the MCS/2H

Operation Manual or F4G User’s Manual.

6. Transmit the Proper data.

Transmit the Proper data from the host computer to the machine. The Proper data

can be sent either before or after zero-setting is done provided that the Proper data is

transmitted before any command function keys are pressed.

7. Transmit the program.

Transmit the program from the host computer to the machine.

Caution: Proper data that is valid for the machine must have been transmitted, before a

program can be transmitted. If valid Proper data does not exist when a program is

transmitted, the program check will not be carried out successfully and a transmission

error will occur even if the program is valid.

Note: For information on creating programs, refer to the MCS/2H Programming Manual or

F4G User’s Manual.

Part 2 Chapter 1 Basic Operation

Edition 1.1 2-1-17 CP643E System Reference

8. Cut the power, and then restart the machine.

Even though the power has been cut, the status data, Proper data and programs will

remain in the machine.

After this, continue with normal operation.

I/O Check Start

This subsection explains how to enter the I/O check mode.

Press the [F1] function key and hold it down while pressing the POWER ON button.

This will bring the machine directly into I/O Check Mode. For further information on

I/O check operation, refer to Part 3, “Commands”.

Caution: When I/O check start is used to start the machine, the 200V power does not come on.

When the RETURN command is used to leave the I/O Check mode, the 200V power is

restored and a zero-setting operation is enabled.

Part 2 Chapter 1 Basic Operation

Edition 1.1 2-1-18 CP643E System Reference