CP643 系统参考.pdf - 第203页
POSITION 1 514-2-4-1 Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [ADJ. TEST] - [POSITION 1] Press to conduct a conveyor width adjustment test. Enter a value from the numerical keypad. Revision History POSITIO…
CODE READ 514-2-3
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [CODE READ]
Press to start a bar code reader test when the ID conveyor is using the bar code reader.
Note: For further details refer to the ‘HELPS Operation Manual’.
Revision History
READER 1 514-2-3-1
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [CODE READ] - [READER 1]
Press to perform a test reading of the bar code on the upper surface of the board.
Revision History
READER 2 514-2-3-2
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [CODE READ] - [READER 2]
Press to perform a test reading of the bar code on the lower surface of the board.
Revision History
ADJ. TEST 514-2-4
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [ADJ. TEST]
This command provides entry to the command page for measuring the Proper data necessary for
width adjustment when conveyor width adjustment is carried out automatically.
Note: Refer to "HELPS Operation Manual" for further details.
Revision History
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-42 CP643E System Reference
POSITION 1 514-2-4-1
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [ADJ. TEST] - [POSITION 1]
Press to conduct a conveyor width adjustment test. Enter a value from the numerical keypad.
Revision History
POSITION 2 514-2-4-2
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [ADJ. TEST] - [POSITION 2]
Press to conduct a conveyor width adjustment test. Enter a value from the numerical keypad.
The conveyor will move between position 1 and position 2.
Revision History
OFFSET 514-2-4-3
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [ADJ. TEST] - [ OFFSET]
Press to enable the operator to set a conveyor offset value into Proper data (27. Conveyor Stop
Offset). This value should be entered from the numerical input keypad.
The entry range is 0 mm to 1 mm.
Revision History
TARGET 514-2-4-4
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [ADJ. TEST] - [ TARGET]
Press to set the conveyor width target. The width will change from the setting in position 1 to
position 2 or vice versa when this key is pressed.
Revision History
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-43 CP643E System Reference
RCOM RESET 514-2-5
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [RCOM RESET]
Press to clear the contents of communication status memory. If the remote commands are not
operating correctly, use this command to reset the communication status.
Revision History
HOST 514-3-0
Command Pass : [SET] - [STATUS] - [LINE MODE] - [HOST]
Press this command to specify whether or not remote commands are to be used (this command only
displays when the SECS/GEM communication protocol is used).
Revision History
REMOTE / LOCAL 514-3-1
Command Pass : [SET] - [STATUS] - [LINE MODE] - [HOST] - [REMOTE / LOCAL]
Press this command to toggle the remote command mode.
REMOTE: Enables remote commands from the host.
LOCAL: Disables commands from the host.
Revision History
ETC 515-0-0
Command Pass : [SET] - [STATUS] - [ETC]
Press to access further commands.
Revision History
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-44 CP643E System Reference