CP643 系统参考.pdf - 第368页

1. Standard I/O Input 1 MX250 Address 0xef0200 LED No. No. Display Description A00 X000 EMERGENCY SW Emergency stop button A01 X001 START SW Start button A02 X002 RESET SW Reset button A03 X003 CYCLE STOP SW Cycle stop b…

Part 6 I/O Map

1. Standard I/O

Input 1 MX250 Address 0xef0200

LED No. No. Display Description

A00 X000 EMERGENCY SW Emergency stop button

A01 X001 START SW Start button

A02 X002 RESET SW Reset button

A03 X003 CYCLE STOP SW Cycle stop button

A04 X004 TM COUNT1 New time counter 2000 hours expired

A05 X005 TM COUNT2 New time counter 6000 hours expired

A06 X006 (Reserved)

A07 X007 (Reserved)

A08 X008 INCHING RIGHT Inching right key

A09 X009 INCHING LEFT Inching left key

A0A X00A INCHING DOWN Inching down key

A0B X00B INCHING UP Inching up key

A0C X00C INCHING CW Inching clockwise key

A0D X00D INCHING CCW Inching counterclockwise key

A0E X00E (Reserved)

A0F X00F SHIFT KEY Shift key

B00 X010 F1 Function key F1

B01 X011 F2 Function key F2

B02 X012 F3 Function key F3

B03 X013 F4 Function key F4

B04 X014 F5 Function key F5

B05 X015 F6 Function key F6

B06 X016 (Reserved)

B07 X017 – (MINUS KEY) Minus key

B08 X018 E1 Numerical key 1

B09 X019 E2 Numerical key 2

B0A X01A E3 Numerical key 3

B0B X01B E4 Numerical key 4

B0C X01C TENKEY 1 Numerical key 1

B0D X01D TENKEY 2 Numerical key 2

B0E X01E TENKEY 4 Numerical key 4

B0F X01F TENKEY 8 Numerical key 8

Part 6 Chapter 1 Standard I/O

Edition 1.0 6-1-1 CP643E System Reference

Input 2 MX250 Address 0xef0220

LED No. No. Display Description

A00 X020 MACHINE READY Machine is ready

A01 X021 AIR OK Air pressure check switch

A02 X022 THERMAL OK Thermal sensors functional

A03 X023 SERVO READY Servos functional

A04 X024 (Reserved)

A05 X025 Short circuit

A06 X026 Short circuit

A07 X027 Short circuit

A08 X028 FRONT DOOR OK Front door safety switch

A09 X029 REAR DOOR OK Rear door safety switch

A0A X02A LOADER PLC OK Board loader PLC functional

A0B X02B VACUUM OK Vacuum pressure check switch

A0C X02C CAM HANDLE CHK Cam handle switch

A0D X02D FEEDER CHK Feeder lifted

A0E X02E FENCE1 CHK Rear fence 1

A0F X02F FENCE2 CHK Rear fence 2

B00 X030 (Reserved)

B01 X031 BACKUP PIN CHK Backup pin detection

B02 X032 (Reserved)

B03 X033 PCB SET OK Reference pin inserted

B04 X034 FLWUP RAIL OUT Followup rail clutch engaged (outside)

B05 X035 FLWUP RAIL IN Followup rail clutch engaged (inside)

B06 X036 HARD READY Hardware ready

B07 X037 FEEDER CHK 18ST Station 18 interference (V1.34)

B08 X038 CONV PLUS OT Conveyor width (+) overtravel

B09 X039 CONV MINUS OT Conveyor width (-) overtravel

B0A X03A CONV PCB CHK Board on conveyor

B0B X03B REAR OPERATION Machine operated from rear panel

B0C X03C FEEDING FW POS Station 1 feeding lever advance limit

B0D X03D FEEDING BW POS Station 1 feeding lever retract limit

B0E X03E CAM ZERO POS Cam origin position

B0F X03F ST11 DN POS Station 11 cylinder lower limit (V1.41)

Part 6 Chapter 1 Standard I/O

Edition 1.0 6-1-2 CP643E System Reference