CP643 系统参考.pdf - 第241页

HT REST (Displayed for Handy T erminal) 524-1-0 Command Pass: [SET] - [MANUAL] - [HT] - [HT RESET] If the Handy Terminal hangs up for some reason then this key can be pressed to reset or reinitialize the Handy Terminal. …

▲ 523-2-3

Command Pass: [SET] - [MANUAL] - [NOZZLE] - [SKIP NOZZLE] - [▲]

Press to move the cursor up one line.

Revision History

▼ 523-2-4

Command Pass: [SET] - [MANUAL] - [NOZZLE] - [SKIP NOZZLE] - [▼]

Press to move the cursor down one line.

Revision History

SKIP/CLEAR 523-2-5

Command Pass: [SET] - [MANUAL] - [NOZZLE] - [SKIP NOZZLE] - [SKIP/CLEAR]

Align the cursor with the desired nozzle and press this key to manually set the nozzle to be

skipped. "SKIP" will display in yellow beside the nozzle. Use the same key to cancel the skip

setting. When the cursor is set at a nozzle which has been set to be skipped, the command will

change to “CLEAR”.

Revision History

HT (Displayed for Handy Terminal) 524-0-0

Command Pass: [SET] - [MANUAL] - [HT]

Press to enter commands related to the Handy Terminal.

An ID code is necessary for entering this command. This command will not appear if the Handy

Terminal option is not used.

Revision History

Part 3 Chapter 3 Command Descriptions

Edition 1.0 3-3-80 CP643E System Reference

HT REST (Displayed for Handy Terminal) 524-1-0

Command Pass: [SET] - [MANUAL] - [HT] - [HT RESET]

If the Handy Terminal hangs up for some reason then this key can be pressed to reset or reinitialize

the Handy Terminal.

Revision History

BC TEST (Displayed for Handy Terminal) 524-2-0

Command Pass: [SET] - [MANUAL] - [HT] - [BC TEST]

Press to carry out a bar code read test.

Revision History

HT RESET (Displayed for Handy Terminal) 524-2-1

Command Pass: [SET] - [MANUAL] - [HT] - [BC TEST] - [HT RESET]

This command is not available during the BC TEST processing.

Revision History

CODE READ (Displayed for Handy Terminal) 524-2-2

Command Pass: [SET] - [MANUAL] - [HT] - [BC TEST] - [CODE READ]

When this key is pressed it becomes possible for the Handy Terminal to read bar codes. When a

code is read it will display as shown above. If the type of bar code changes it is possible to check to

see if the new code can be read.

Revision History

Part 3 Chapter 3 Command Descriptions

Edition 1.0 3-3-81 CP643E System Reference

PROPER 530-0-0

Command Pass: [SET] - [PROPER]

Press to make Proper Data measurements. To use this command the operator must enter an ID

code.

Revision History

CAMERA 531-0-0

Command Pass: [SET] - [PROPER] - [CAMERA]

Press to set camera related Proper data.

Revision History

XC/YC 531-1-0

Command Pass: [SET] - [PROPER] - [CAMERA] - [XC/YC]

Press to measure the mark camera reading position.

Revision History

SET 531-1-1

Command Pass: [SET] - [PROPER] - [CAMERA] - [XC/YC] - [SET]

Press to set the present position for the XY-table as Mark Read Pos. XC/YC.

Caution: Before performing this command, move the XY-table to the center position of the mark setting jig.

After performing this command, make sure to perform mark camera position measurement and

camera tilt measurement (command page 531-2).

Revision History

Part 3 Chapter 3 Command Descriptions

Edition 1.0 3-3-82 CP643E System Reference