CP643 系统参考.pdf - 第302页
9: User_Define A 0000 0000 0000 0000 $# Currently not in use. Default: 0000 0000 0000 0000 11: Machine_Status A 0000 0000 0000 0000 * This sets special mode parameters (input as a 16 bit binary mask pattern) that are com…
[Signal Tower Setting Method]
Fuji uses the following standards for signal tower operation.
Automatic operation............................................Blue (Green) Light
Loader operating.................................................Blue (Green) Light
Waiting for PCB ..................................................Blue (Green) Flash
Waiting for NEXT................................................Blue (Green) Flash
Out of parts soon ................................................Yellow Light
Out of parts: machine stopped............................Yellow Flash
Abnormal occurrence: machine stopped ............Red Flash
Statistical Error Alarm.........................................Yellow Light
In changeover: operator called ..........................Yellow Flash
Vision process error............................................Red Light
Machine waiting..................................................Blue (Green) Flash
In changeover.....................................................Blue (Green) Flash
Production complete: machine stopped..............Yellow Flash
The bit map and the corresponding display is shown below.
Display Bit map Decimal
Reserved 1000 0000 0000 0000 32768
Reserved 0100 0000 0000 0000 16384
Production complete: machine stopped 0010 0000 0000 0000 8192
Display messages from the HOST (SECS/GEM) 0001 0000 0000 0000 4096
In changeover 0000 1000 0000 0000 2048
Vision processing error 0000 0100 0000 0000 1024
Automatic operation 0000 0010 0000 0000 512
Loader operating 0000 0001 0000 0000 256
Waiting for PCB 0000 0000 1000 0000 128
Waiting for NEXT 0000 0000 0100 0000 64
Out of parts soon 0000 0000 0010 0000 32
Out of parts: machine stopped 0000 0000 0001 0000 16
Abnormal occurrence: machine stopped 0000 0000 0000 1000 8
Statistical Error Alarm 0000 0000 0000 0100 4
In changeover: operator called 0000 0000 0000 0010 2
Machine waiting 0000 0000 0000 0001 1
[Example] This is the Fuji standard signal tower blue flash setting
Machine waiting 0000 0000 0000 0001
Waiting for NEXT 0000 0000 0100 0000
Waiting for PCB 0000 0000 1000 0000
In changeover +0000 1000 0000 0000
Total 0000 1000 1100 0001
The user may set his own standards in this manner.
Part 4 Chapter 2 Details of Proper Data
Edition 1.1 4-2-2 CP643E System Reference
9: User_Define A 0000 0000 0000 0000 $#
Currently not in use.
Default: 0000 0000 0000 0000
11: Machine_Status A 0000 0000 0000 0000 *
This sets special mode parameters (input as a 16 bit binary mask pattern) that are common
to every machine.
Ensure the printer is connected when outputting to a printer. Production cannot be
guaranteed when outputting to a printer as this is for development only.
Default: 0000 0000 0000 0000
Special mode Bit map Decimal
The mark compensation value is printed out. 1000 0000 0000 0000 32768
The first device offset is printed out during automatic 0100 0000 0000 0000 16384
operation.
Global skip mark enabled. 0000 0000 1000 0000 128
Check mode for all devices. 0000 0000 0100 0000 64
Machine stops if all the blocks are skipped. The block 0000 0000 0010 0000 32
skip marks are reread when the machine is restarted.
The number of parts used by each nozzle is reported 0000 0000 0001 0000 16
(production data).
Remote commands enabled. 0000 0000 0000 1000 8
Board check by means of block skip marks 0000 0000 0000 0100 4
Set to enter the [MARK EDITOR] command if a mark 0000 0000 0000 0001 1
reading error occurs.
Part 4 Chapter 2 Details of Proper Data
Edition 1.1 4-2-3 CP643E System Reference
Part 4 Chapter 2 Details of Proper Data
Edition 1.1 4-2-4 CP643E System Reference
12: Machine_Status B 0000 0000 0000 0000 #
This sets special mode parameters (input as a 16 bit binary mask pattern) that are common
to every machine.
Ensure the printer is connected when outputting to a printer. Production cannot be
guaranteed when outputting to a printer as this is for development only.
Default: 0000 0000 0000 0000
Special mode Bit map Decimal
Set when the vision processing debug mode is 1000 0000 0000 0000 32768
specified for nozzle center measurement.
Print out the results of the X, Y-axis placement 0100 0000 0000 0000 16384
position calculations.
Print out the results of nozzle center measurement. 0010 0000 0000 0000 8192
This is a debug function for checking the vision 0001 0000 0000 0000 4096
processing compensation values.
The device shaft advance return mode is not used. 0000 0100 0000 0000 1024
Not in use. 0000 0000 1000 0000 128
The parts reloading position on the CP-6 is 0000 0000 0100 0000 64
changed from 45 to 55.
Change the data check standard. If this bit is set, 0000 0000 0010 0000 32
the PD pickup offset (22.D_ofst_x) for devices
1, 70, 71 and 140 is satisfactory if it is within
± 5.0 mm.
Parts interference prevention (Z-axis positioning). 0000 0000 0001 0000 16
XY-table acceleration/deceleration mode. Controls 0000 0000 0000 1000 8
the speed of the XY-table when it is moved to the
loading position and the board check position.
Do not perform D-axis premovement if there is a 0000 0000 0000 0100 4
block skip mark.
Change placement specifications according to 0000 0000 0000 0010 2
part height.
Skip nozzles which caused an error during nozzle 0000 0000 0000 0001 1
center measurement.
13: Machine_ID 0000 0000 0000 0000 *
This is one of the machine’s special operating parameters (input as a 16 bit binary mask
pattern).
Default: 0000 0000 0000 0000
Special mode Bit map Decimal
0603 (in. 0201) Parts Camera is used. 0000 0000 0000 0010 2