CP643 系统参考.pdf - 第308页
75: MAN Permission Non: Permit # This sets whether or not data can be input from the keypad on the Handy Terminal. Non: Keypad cannot be used Permit: Keypad can be used Default: "Permit” 76: HT Comment Term. Code AS…
56: Terminal Type CRX1200: VT-100 $
Not currently in use.
Default: "CRX1200”
57: Code Terminal Port 0 ~ 30 #
When a Handy Terminal is used to re-read a barcode, this sets the 6-channel port number
for the code reader.
0: Handy Terminal is not used for re-reading.
1 - 10: Do not specify 1 to 10.
11 - 30: Port numbers. On a 6-channel board the valid settings are 11 to 16.
Default: 0
70: Device Check SW No: Parts: Miss: Error #
This sets whether or not a compulsory device check will be performed after running out of
parts, or after a program has been changed.
No: No mandatory device check
Parts: Perform mandatory device check when parts run out.
Miss: Perform mandatory device check when parts run out or when parts are mispicked.
Error: Perform mandatory device check when parts run out, parts are mispicked or when
a vision processing error occurs.
Default: "Parts"
71: Verifier Tool Non: Barcode: Handy_term #
This sets the hardware used for device check.
Non: Handy Terminal not used
Barcode: Do not use this setting
Handy_term: Handy Terminal used
If “Barcode” is used, the device check may not work.
Default: "Non"
72: Barcode Reader Type 0 ~ 9 #
This sets the type of bar code reader used in device check.
0: Not used
Ensure this is set to “5” (HC-70-FK) if this Proper data item is used.
Default: 0
73: Device Check Port 0 ~ 30 #
If a Handy Terminal is used during device check, this sets the 6-channel port number.
0: Handy Terminal not used
1 - 10: Do not specify 1 to 10.
11 - 30: Port numbers. On a 6-channel board the valid settings are 11 to 16.
Default: 0
74: ESC Permission Non: Permit #
This sets whether or not the [ESC] command can be used during device check.
Non: [ESC] command cannot be used
Permit: [ESC] command can be used
Default: "Permit”
Part 4 Chapter 2 Details of Proper Data
Edition 1.1 4-2-8 CP643E System Reference
75: MAN Permission Non: Permit #
This sets whether or not data can be input from the keypad on the Handy Terminal.
Non: Keypad cannot be used
Permit: Keypad can be used
Default: "Permit”
76: HT Comment Term. Code ASCII CODE #
The Handy Terminal will disregard the comments embedded in the selected ASCII code.
Default: "%”
77: HT Verify Term. Code ASCII CODE #
The Handy Terminal will disregard any comments thereafter.
Default: “/”
78: D Change Trigger Error: Parts: Miss PD #
This sets the conditions under which device change (to the next device) is carried out.
Error: Carried out if parts run out, if parts are mispicked or if there is a vision processing
error.
Parts: Carried out if parts run out.
Miss: Carried out if parts run out or if parts are mispicked.
PD: Carried out according to the conditions laid out in Part data.
Default: "Error”
80: HT. Check Character #
This is used to enable the check character for the Handy Terminal.
No: Check character is not used.
Yes: Check character is used.
Default: “No”
100: FQ Origin Position -30000 ~ 30000 [pulse] ✩*
This is the position of the FQ-axis after the zero set procedure is completed.
As for the value of this Proper data item, the standard position is the position where the
station 10 nozzle shaft engages the clutch. This item should be treated with extreme
caution. If this value is changed station 10 rotation may not be possible and in the worst
case scenario it can lead to damage to the machine.
It is necessary to remeasure this value when the motor has been changed. On the FQ-axis, 1
pulse is 0.05 degrees.
Default is the Proper data calibration result.
101: FRQ Origin Position -30000 ~ 30000 [pulse] ✩*
This is the position of the FRQ-axis after the zero set procedure is completed.
As for the value of this Proper data item, the standard position is the position where the
station 12 nozzle shaft engages the clutch. This item should be treated with extreme
caution. If this value is changed station 12 rotation may not be possible and in the worst
case scenario it can lead to damage to the machine.
It is necessary to remeasure this value when the motor has been changed. On the FRQ-axis,
1 pulse is 0.05 degrees.
Default is the Proper data calibration result.
Part 4 Chapter 2 Details of Proper Data
Edition 1.1 4-2-9 CP643E System Reference
102: NC Origin Position -30000 ~ 30000 [pulse] ✩*
This is the position of the NC-axis after the zero set procedure is completed.
As for the value of this Proper data item, the standard position is the position where the
station 18 nozzle head engages the clutch. This item should be treated with extreme
caution. If this value is changed station 18 rotation may not be possible and in the worst
case scenario it can lead to damage to the machine.
It is necessary to remeasure this value when the motor has been changed. On the NC-axis, 1
pulse is 0.02 degrees.
Default is the Proper data calibration result.
103: Pickup Position T1 -500000 ~ 0 [pulse] ✩*
This sets the range of movement of the D1-axis from it's location when zeroing is completed
to the pickup position of device one.
This is a reference position for picking parts. If this value changes parts will not be picked.
A worst case scenario would involve damage to the machine, so exercise extreme caution.
When the motor is changed, this position must be measured again.
On the D1-axis, one pulse is 0.00853 mm.
Default is the Proper data calibration result.
104: Pickup Position T2 0 ~ 500000 [pulse] ✩*
This sets the range of movement of the D2-axis from it's location when zeroing is completed
to the pickup position of device 71.
This is a reference position for picking parts. If this value changes parts will not be picked.
A worst case scenario would involve damage to the machine, so exercise extreme caution.
When the motor is changed, this position must be measured again.
On the D2-axis, one pulse is 0.00853 mm.
Default is the Proper data calibration result.
105: Origin Position Z -65000 ~ 65000 [pulse] ✩*
This specifies the Z-axis range of movement from the bottom surface of the PCB at the zero
set complete position on the XY-table to the position where the No. 1 nozzle on head A at
station 11 rises 0.3 mm above its lower dead point.
Exercise extreme caution when handling this item since a change in this value can cause the
nozzle to press parts into the PCB with too much force or cause parts to fall off.
This item must be measured again when the motor is replaced. On the Z-axis, one pulse is
0.002 mm.
Default is the Proper data calibration result.
106: Placing Position X -100000 ~ 0 [pulse] ✩*
This sets the X-coordinate for positioning the reference pin directly below the No.1 nozzle
on the A head when this nozzle stops at station 11 after moving from the X-axis zeroing
position.
This is the placing position reference value in the X direction. If this value changes there can
be no confidence in the accuracy of the X direction placing position.
When the motor is changed, this position must be measured again.
On the X-axis, one pulse is 0.01 mm.
Default is the Proper data calibration result.
Part 4 Chapter 2 Details of Proper Data
Edition 1.1 4-2-10 CP643E System Reference