CP643 系统参考.pdf - 第350页
2.2 Machine Status The messages displayed here indicate the status of the machine. Ready The machine is idle and is waiting for the operator to press one of the function keys. Zero Setting The machine is currently perfor…
2. Other Messages
This chapter describes non error messages.
2.1 Requests to the Operator
Machine Not Zero Set
The machine is waiting for the operator to press the START button to carry out zero
setting.
Press START
The machine is waiting for the operator to press the START button.
Waiting for Reset SW
The machine is waiting for the operator to press the RESET button.
Turn Off Power
The machine is waiting for the operator to press the POWER OFF button.
D??? Supply
The feeder at the device position shown is out of parts.
D??? Check
The feeder at the device position shown has parts but they are not being picked up.
D??? unable to process
Vision processing cannot process the part picked.
Invalid Command
Data was improperly entered and must be reentered.
Outside Movement Area
Since the data that has been input has caused the axis to move outside the permissible
range of movement, the machine is waiting for the data to be reentered.
Sequence End Stop
One board has been produced, and the machine is awaiting the next command.
Production Complete
Scheduled production is complete, and the machine is awaiting the operator’s next
command.
Set Proper
Machine is waiting for Proper data to be set. Set the correct Proper data.
Measure Nozzle Centers
After nozzles have been changed or after anything else occurs which makes it possible
that nozzle center values may have changed, a request will display to carry out nozzle
center measurement
Origin not Found
Machine is waiting for the START button to be pushed so that origin position search can
be started.
Part 5 Chapter 2 Other Messages
Edition 1.0 5-2-1 CP643E System Reference
2.2 Machine Status
The messages displayed here indicate the status of the machine.
Ready
The machine is idle and is waiting for the operator to press one of the function keys.
Zero Setting
The machine is currently performing zero-setting on all axes.
Operating Loader…
A board is being loaded or unloaded.
Waiting for PCB…
The machine is ready to receive a board.
Waiting for NEXT
The machine has finished processing the board and is waiting for the next board.
Stop After Current Board
The machine will stop when the board currently being produced is finished.
Measuring Proper
The machine is measuring Proper data.
Normal Turnover
In turnover mode, sequences are executing in normal order.
Reverse Turnover
In turnover mode, sequences are executed in reverse order.
Discard picked part
All nozzles with picked up parts will be discarding those parts in the discard box.
Changing over
The machine is in the middle of automatic changeover.
Using Handy Terminal
The Handy Terminal is currently being used.
Return to Cam Zero
Cam axis is returning to its origin position.
Calculating Placing Data
Data necessary for placing parts is being processed.
Vision Processor Executing
Machine is waiting for vision processing to be completed.
Part 5 Chapter 2 Other Messages
Edition 1.0 5-2-2 CP643E System Reference
3. MCS Error Codes
This chapter explains the MCS error codes that are especially related to transmission with HELPS
compatible machines.
Error Code: 2200750B
MCS Display: DTX750B Error
[Cause]: The transmit descriptor filename could not be obtained.
[Remedy]: Make sure that the machine is correctly registered in the Line Descriptor.
The MCS30 must be reset after data is entered in the Line Descriptor. Exit
MCS2H (if the LMS system is also installed exit LMS). Turn the MCS30
power supply off and then back on.
Error Code: 22007511
MCS Display: DTX7511 Error
[Cause]: The program requested by the machine cannot be opened.
[Remedy]: Make sure that the program requested is stored in the MCS30 computer.
This can be checked using the function key [Dir_H].
Error Code: 22007512
MCS Display: DTX7512 Error
[Cause]: The MCS30 computer was in the process of transmitting a program when a
program transmission request was received from the machine (the
communication pipe was being used when the download request came
from the machine).
[Remedy]: After waiting awhile, perform the download request again. If the error
still occurs at that time, shut off the power to the MCS30 computer.
Error Code: 22007514
MCS Display: DTX7514 Error
[Cause]: The program’s machine type does not match the previously transmitted
program machine type.
[Remedy]: Make sure program machine types match.
Error Code: 22007515
MCS Display: DTX7515 Error
[Cause]: After a download request was made, an error occurred in the MCS2H
program check.
[Remedy]: Verify the program.
Error Code: 2200AB00
MCS Display: DTXAB00 Error
[Cause]: After a download request was made, an answer was not received from the
machine within the preset time limit.
[Remedy]: Verify that the machine and MCS30 are both booted up.
Part 5 Chapter 3 MCS Error Codes
Edition 1.0 5-3-1 CP643E System Reference