CP643 系统参考.pdf - 第202页
CODE READ 514-2-3 Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [CODE READ] Press to start a bar code reader test when the ID conveyor is using the bar code reader. Note: For further details refer to the ‘HELPS…
LMS 514-2-0
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS]
Press to access LMS related commands.
The user must input an ID code to enter this mode.
Revision History
CELL STATUS 514-2-1
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [CELL STATUS]
Press to change cell status.
Caution: When the cell status is changed it is also necessary to change the LMS data. Once this is done the
LMS must be shut down and rebooted. Furthermore, if this key is pressed it is necessary to shut
down the power to the machine and reboot in order to initialize the machine too.
Revision History
INITIALIZE 514-2-2
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [INITIALIZE]
Press to clear the contents of changeover memory. If for some reason changeover is interrupted
before completion, this key can be pressed to return to the original status.
Caution: When in HELPS compatible operation, changeover status is stored in memory when the power is cut,
so care should be taken not to press this key when it is not necessary. Furthermore, if this key is
pressed it is necessary to shut down the machine and reboot in order to initialize the machine.
Revision History
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-41 CP643E System Reference
CODE READ 514-2-3
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [CODE READ]
Press to start a bar code reader test when the ID conveyor is using the bar code reader.
Note: For further details refer to the ‘HELPS Operation Manual’.
Revision History
READER 1 514-2-3-1
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [CODE READ] - [READER 1]
Press to perform a test reading of the bar code on the upper surface of the board.
Revision History
READER 2 514-2-3-2
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [CODE READ] - [READER 2]
Press to perform a test reading of the bar code on the lower surface of the board.
Revision History
ADJ. TEST 514-2-4
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [ADJ. TEST]
This command provides entry to the command page for measuring the Proper data necessary for
width adjustment when conveyor width adjustment is carried out automatically.
Note: Refer to "HELPS Operation Manual" for further details.
Revision History
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-42 CP643E System Reference
POSITION 1 514-2-4-1
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [ADJ. TEST] - [POSITION 1]
Press to conduct a conveyor width adjustment test. Enter a value from the numerical keypad.
Revision History
POSITION 2 514-2-4-2
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [ADJ. TEST] - [POSITION 2]
Press to conduct a conveyor width adjustment test. Enter a value from the numerical keypad.
The conveyor will move between position 1 and position 2.
Revision History
OFFSET 514-2-4-3
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [ADJ. TEST] - [ OFFSET]
Press to enable the operator to set a conveyor offset value into Proper data (27. Conveyor Stop
Offset). This value should be entered from the numerical input keypad.
The entry range is 0 mm to 1 mm.
Revision History
TARGET 514-2-4-4
Command Pass : [SET] - [STATUS] - [LINE MODE] - [LMS] - [ADJ. TEST] - [ TARGET]
Press to set the conveyor width target. The width will change from the setting in position 1 to
position 2 or vice versa when this key is pressed.
Revision History
Part 3 Chapter 3 Command Descriptions
Edition 1.0 3-3-43 CP643E System Reference