YV180X_Ope_E.pdf - 第197页

5 -121 EPD8013110 Operation Chapter 5 5 Creating the PCB data 10.2 Star ting the test mount Now , try producing only one PCB to check how components ar e mounted. W e recommend using a PCB with double-sided tape affix ed…

-120

EPD8013110

Operation

Chapter 5

Creating the PCB data

3. Press the emergency stop button, and set the PCB on the conveyor to

confirm that the width is correct. If not correct, quit automatic opera-

tion by executing the <1/1/E0 EXIT FROM RUNNING> command, then

select <1/2/PRD. DATA> - ”PCB Info.” to correct the “PCB Size” Y data.

4. After checking the conveyor width, adjust the locate pin and push-up

pin positions so that the PCB can be clamped on the conveyor. Finally,

remove the PCB.

Reference

Refer to “8. Changing the conveyor unit setup” in Chapter 4 for details on the conveyor

unit setups.

4 Set up the components (feeder set).

Run the <1/1/D4 ASSISTANT UTILITY> command, and select “COMPO-

NENT ASSIGNMENT” to check the setup of the components. A list of

feeder mounting positions appears as shown below.

COMPONENT ASSIGNMENT screen

27552-C0-00

No.

Feeder Type

8mmTape

Component Name

MINI_TR

R2125

R3126

R1608

R2125

MINI_TR

SetNo.

F10

F11

F12

F13

F14

F15

F16

Counter / Total

↑

↓

<<MODE>> 1/RUNNING

<COMMAND_LIST> D/INITIALIZE

D4 ASSISTANT UTILITY

ASSISTANT UTILITY

COMPONENT ASSIGNMENT

Reference

For details on the component setups, refer to the separate feeder user’s manual.

-121

EPD8013110

Operation

Chapter 5

Creating the PCB data

10.2 Starting the test mount

Now, try producing only one PCB to check how components are mounted.

We recommend using a PCB with double-sided tape affixed across the

mounting position.

1 Unplug the PREVIOUS INTERFACE connector

When the mounter is installed on a production line, unplug the GATE-IN

(PREVIOUS INTERFACE) connector on the lower right panel on the front of

the machine. If you perform a mounting test with this connector still

plugged, the PCB may flow into the downstream process after component

mounting, or the PCB may drop.

GATE-IN (PREVIOUS INTERFACE) connector

23553-D8-00

INTERFACE

2 Set the operation speed.

Press the [SPEED] key on the YPU, or select the <1/1/D6 RUNNING

UTILITY> - ”RUNNING SPEED” command, then set the speed to approx.

40 to 60%.

Speed setting box

27553-C0-00

Spead1 =

Spead2 =

Spead3 =

Spead4 =

Spead5 =

100

-122

EPD8013110

Operation

Chapter 5

Creating the PCB data

3 Start operation.

Check safety and then start PCB production as follows.

1. Place the PCB at the conveyor entrance so the entrance sensor

responds to the PCB.

Entrance sensor

23554-D8-00

Transfer

direction

Entrance sensor

PCB

2. Run the <1/1/A2 AUTO RUNNING> command or press the [RUN] key

to start operation.

3. Run the <1/1/D6 RUNNING UTILITY> - ”CONVEY OUT PCB”

command.

This command carries out the PCB without requesting the machine to

carry in the next PCB.

CONVEYOR OUT PCB command

27554-C0-00

<<<APPLICATION>>> 1/OPERATION/M

<<MODE>> 1/RUNNING

<COMMAND_LIST>

D/INITIALIZE

RUNNING UTILITY

CONVEY OUT PCB

Condition

PCB out

REfertence

For details on the CONVEYOR OUT PCB command, refer to “6. Finishing the PCB

production” in Chapter 4.

4 Proceed as follows if an error occurs.

If an error occurs during PCB data loading, component pickup or compo-

nent mounting, press the [Space] bar to temporarily stop the machine,

check the cause of the problem and take corrective action referring to the

next section, “10.3 Error countermeasures during mounting test”. To

resume operation after correcting the problem, press the [Space] bar again.

WARNING

NEVER ENTER ANY PART OF THE BODY IN THE AXIS MOVEMENT AREA OF

THE MOUNTER EVEN DURING TEMPORARY STOP. ALWAYS PRESS THE

EMERGENCY STOP BUTTON BEFORE ACCESSING A PART IN THE AXIS

MOVEMENT AREA.