Q170226E01.pdf - 第313页
RH5 8.3 List of Jumper Switch Settings SERVICE MANUAL 8.3−16 DA3SEC−85−540−B0 8.3.4 MIOE (I) Board Setting SW1: Generates reset signal. 1 2 3 BPS 0 0 0 9600 1 0 0 4800 0 1 0 2400 1 1 0 1200 0 0 1 600 1 0 1 300 4: Brake c…
8.3 List of Jumper Switch Settings
SERVICE MANUAL
RH5
8.3−15
DA3SEC−85−540−B0
Jumper switch settings
(1) JP4, JP7 (Fixed)
JP4
JP7
1
1
(2) JZ1, JZ2 (Fixed)
JZ4
JZ2
1
1
(3) Camera cable (Fixed)
JZ3
JZ4
1
1
When Straight cable is used.
When L type cable is used.
=REFERENCE=
x Factory setting is for Straight cable
RH5
8.3 List of Jumper Switch Settings
SERVICE MANUAL
8.3−16
DA3SEC−85−540−B0
8.3.4 MIOE (I) Board Setting
SW1: Generates reset signal.
1 2 3 BPS
0 0 0 9600
1 0 0 4800
0 1 0 2400
1 1 0 1200
0 0 1 600
1 0 1 300
4: Brake character
ON: Output
OFF: Not output
5: Checksum
ON: Yes
OFF: No
6: R recommend
ON: Output
OFF: No output
7: Time out
ON: Yes
OFF: No
8: End code
ON: CR
OFF: ETX
1:
2:
3:
4:
5:
6:
7:
8:
=REFERENCE=
JP17 (FDD) setting
For PC98 series For IBM PC series
JP17 − 1: Open JP17 − 1: Open
JP17 − 2: Short JP17 − 2: Open
JP17 − 3: Open JP17 − 3: Open
8.3 List of Jumper Switch Settings
SERVICE MANUAL
RH5
8.3−17
DA3SEC−85−540−B0
Switch List
Switch No. Function Description
1 Reset signal generation 5
2 NMI signal generation 5
3
4 Switch for setting (x 8) 2
5 Switch for setting(x 4) 2
6 Leader start signal switching 4
7 TTY output data switching 4
8 TTY input data switching 4
9 TTY input data switching 4
10 Busy signal switching 4
11 Busy signal switching 4
12 Dual port RAM address setting on the bus side 1
Jumper List
Jumper
No.
Function Description
1 Selects RXC of HOST 4
2 Selects TXC of HOST 4
3 Selects CCLK output 6
4 Selects BCLK output 6
5 Selects TXC/RXC for TTY 4
6 Selects CTS for TTY 4
7
8 Selects RTS for TTY 4
9 Select 82289 6
10 Selects BPRO output 6
11 Selects P2 bus interrupt level 7
12 Selects WD37C65 3
13 Terminates READER START signal 4
14 Pull−up to +12V volts for TTY input data 4
15 Selects TXD for TTY 4
16 Selects RXD for TTY 4
17 Jumper (x 3) for setting 3
18 Selects clock SIO1/2 4
19 Selects TXC/RXC for SIO1 4
20 Selects TXC/RXC for SIO2 4