Q170226E01.pdf - 第9页
RH5 SERVICE MANUAL 6 DA3SEC−02−020−B0 = MEMO =
SERVICE MANUAL
RH5
5
DA3SEC−02−020−B0
7.1.3 AC Motor Power ON 7.1−4..................................................
7.1.4 Manual Mode Movement Check in the Manual Mode 7.1−5......................
7.1.5 Semi−auto Mode Movement Check 7.1−6.....................................
7.1.6 Fine adjustments 7.1−8.....................................................
7.2 AC Servomotor Adjustment 7.2−1...................................
7.2.1 AC Motor Driver Check 7.2−1................................................
7.2.2 AC Motor Power ON 7.2−2..................................................
7.2.3 Manual Mode Movement Check 7.2−2........................................
7.2.4 Semi−auto Mode Movement Check 7.2−3.....................................
7.2.5 Setting/Browsing User Constant (Memory Switch) (Cn−01 and Cn−02) 7.2−18.......
8.3 Digital Operator 7.3−1.............................................
7.3.1 Inputting Offset Value (Cn−00) 7.3−1..........................................
7.3.2 Inputting Bit No. (Cn−01 and Cn−02) 7.3−3....................................
7.3.3 Changing Driver Setting Value (Cn−03 through Cn−23) 7.3−5....................
8. RELATED INFORMATION 8.0−2.......................
8.1 Construction Drawing List 8.1−1....................................
8.1.1 Construction Drawing List (NM−8244A/B/C) 8.1−1..............................
8.1.2 Construction Drawing List (NM−8245A/B/C) 8.1−3..............................
8.2 List of Software Settings 8.2−1.....................................
9.3 List of Jumper Switch Settings 8.3−1................................
8.3.1 CNC−4S (I) Board Setting 8.3−1.............................................
8.3.2 RCG Board Setting (X984 − 204) 8.3−8.......................................
8.3.3 RCG (I) Board Setting (X984 − 211) 8.3−13.....................................
8.3.4 MIOE (I) Board Setting 8.3−16................................................
8.3.5 SEQ−SE (I) Board Setting 8.3−31.............................................
8.3.6 APC Board Setting 8.3−34....................................................
9.4 AC Servomotor Drivers 8.4−1.......................................
8.4.1 X/Y/Z (40−, 62−feeder) and H (Camshaft) Axis Driver 8.4−1......................
8.4.2 Z Axis (80−feeder) Driver 8.4−8..............................................
8.5 Cycle Timer Setting 8.5−1..........................................
8.6 Checking Slow Down, Origin, Limit and Safety Limit Sensors 8.6−1.....
8.7 CNC Board Table Setting 8.7−1.....................................
8.8 Monitoring I/O Signals 8.8−1........................................
8.9 Measuring Belt Tension 8.9−1.......................................
8.9.1 Sonic Tension Meter 8.9−1..................................................
8.9.2 Main Drive Unit 8.9−3.......................................................
8.9.3 Z Axis Driver 8.9−5.........................................................
8.10 Removing Battery from Controller (Panadac 791) 8.10−1...............
8.11 Differences in Specifications between RHIII and RH5 8.11−1...........
RH5
SERVICE MANUAL
6
DA3SEC−02−020−B0
= MEMO =
SERVICE MANUAL
RH5
1.0−1
1ダミー(Sectionのレベル1)
1.0ダミー(Sectionのレベル2)