Q170226E01.pdf - 第379页
RH5 8.8 Monitoring I/O Signals SERVICE MANUAL 8.8−18 DA3SEC−85−520−A0 = MEMO =
8.8 Monitoring I/O Signals
SERVICE MANUAL
RH5
8.8−17
DA3SEC−85−520−A0
ADDRESS LABEL
BLK DEV
7bit 6bit 5bit 4bit 3bit 2bit
1 bit 0 bit COMMENT
701F C (3400)
701F D (3410)
701E 0 (3420)
701E 1 (3430)
701E 2 (3440)
701E 3 (3450)
701E 4 (3460)
701E 5 (3470)
701E 6 (3500)
701E 7 (3510)
701F 4 (3520)
701F 5 (3530)
7 140
147
156
166
176
206
216
226
236
246
256
266 C6
276 C14
145
155
165 T5
175 T13
205
215 T29
225 T37
235 T45
245 T53
255 T61
265 C5
275 C13
146
140
271 C9
251 T57
261 C1
211 T25
221 T33
231 T41
241 T49
141
151
161 T1
171 T9
201
150
160
210
220
170
200
230
250
260
240
270
143
153
163 T3
173 T11
203
213 T27
223 T35
233 T35
243 T51
253 T59
263 C3
273
142
152
162 T2
172 T10
202
212 T26
222 T34
232 T42
242 T50
252 T58
262 C2
144
154
164 T4
174 T12
204
214 T28
224 T36
234 T44
244 T52
254 T60
264 C4
274 C12
Special
dummy area
(3−340)
C11
C8
Special Dummy Table−1 RH5
Special
dummy area
Timer area0
Timer area1
Timer area2
Timer area3
Timer area4
Timer area5
Counter
area1
Counter
area2
Reserved
area
Reserved
area
Reserved
area
Reserved
area
C0
T56
T48
157
167
177
207
217
227
237
247 T55
Turns ON at
INT1−3.
257 T53
267 C7
277 C15
Turns ON at
INT1−2.
7 140
7 140
7 140
7 200
7 200
7 200
7 200
7 200
7 200
7 200
7 200
T7
(3−347)
PC board exists at
insertion position
T15
T31
T39
T47
(3−317)
(3−307)
(3−377)
Signal tower OFF
(3−367)
(3−357)
Unloader
272 C10
T40
T32
T24
(3−360)
T8
T0
(PEND)
Usually ON.
Usually OFF.
(SEND)
Turns ON at
INT1−5.
Turns ON at
INT1−6.
Turns ON at
INT1−7.
Turns ON at
INT1−0.
Turns ON at
INT1−1.
T6
(3−346)
(3−356)
(3−366)
T30
(3−376)
T38
(3−306)
T46
(3−316)
T54
T62
Solenoid/mecha
valve changeover
Signal tower ON
Loading ready error
Invert
(3−345)
Invert
(3−315)
(3−305)
(3−365)
(3−375)
(3−355)
PCB stopper
PCB wait stock 2 PCB wait stock 1
Invert error
PC board exists at
unloader exit.
MEND output
(3−344)
Cutter forward
(3−354)
For positioning (2)
(3−364)
(3−374)
Invert error
Loader normal turn
ON
(3−304)
Belt motor reverse
(3−314)
Not used
Recognition start
(3−373)
Loader
Loader
Recognition start
(3−363)
(3−303)
(3−313)
(3−342)
(3−352)
(3−362)
(3−372)
(3−302)
(3−312)
Vacuum timer 2
Vacuum timer 1
Width adjust axis
reference pin
Thermal ON monitor
Feed monitor
Width adjust axis
Unloader
Turns ON at
INT1−4.
Width adjust STEP +
Width adjust STEP −
Arm reverse timer
For positioning (1)
(3−361)
(3−351)
(3−341)
(3−371)
Loader (edge
positioning)
Width adjust axis
X−Y
PCB exists at
recognition position.
(3−350)
Transfer chuck close H
Transfer chuck close L
(3−370)
(3−300)
Width adjust axis
loader
(3−310)
Unloader belt motor
STOP
Only 1 scan OFF
after init.
Only 1 scan ON
after init.
(3−343)
No component
detection
Vib.
accommodation
PC board punch out
OFF
PC board punch out
ON
(3−343)
RH5
8.8 Monitoring I/O Signals
SERVICE MANUAL
8.8−18
DA3SEC−85−520−A0
= MEMO =
8.9 Measuring Belt Tension
SERVICE MANUAL
RH5
8.9−1
DA3SEC−85−210−A0
8.9 Measuring Belt Tension
DA3SEC−85−210−A0
Sentence No.
8.9.1 Sonic Tension Meter
4
5
1
3
2
=REFERENCE=
Note that sonic tension meter is not included in RH5 and it is not available as a maintenance part.