Q170226E01.pdf - 第8页

SERVICE MANUAL RH5 5 DA3SEC−02−020−B0 7.1.3 AC Motor Power ON 7.1−4 .................................................. 7.1.4 Manual Mode Movement Check in the Manual Mode 7.1−5 ...................... 7.1.5 Semi−auto Mode…

100%1 / 392
RH5
SERVICE MANUAL
4
DA3SEC−02−020−B0
When anvil too high: 5.30−2.............................................
When anvil position is low: 5.30−2........................................
5.31 Recognition Camera Lens Lamp Replacement and Adjustment 5.31−1...
Camera replacement 5.31−1............................................
Acrylic plate replacement 5.31−2.........................................
5.32 Setting Offset Values 5.32−1........................................
Preparations 5.32−1....................................................
Creating NC data 5.32−1................................................
Initial setting of individual machine data 5.32−3.............................
When using a customer’s board 5.32−3...................................
Camera installation 5.32−4..............................................
Camera position adjustment 5.32−5......................................
Automatic camera measuring
(X direction) 5.32−8.............................................................
Supplemental remarks 5.32−9...........................................
Automatic camera offset measuring (Y direction) 5.32−10.....................
Checking Recognition Operation 5.32−12..................................
5.33 Lead Cutter and Tape Cutter Stroke Adjustment 5.33−1................
Cam drive (Stroke adjustment of cutter 2) 5.33−2...........................
Cam drive (Cutting check) 5.33−2........................................
Cylinder drive adjustment 5.33−3........................................
Cylinder drive adjustment (If components are not cut properly:) 5.33−3........
5.34 Axis Height Check and Adjustment 5.34−1...........................
Tape waste check 5.34−1...............................................
Adjusting Z axis height (Raising the Z axis) 5.34−2.........................
Adjusting Z axis height (Lowering the Z axis) 5.34−3........................
5.35 Mechanical Valve Replacement and Adjustment 5.35−1................
Replacing mechanical valve 5.35−1......................................
Adjusting mechanical valve 5.35−1.......................................
5.36 Y Lock Cylinder Replacement and Adjustment 5.36−1.................
Replacing/adjusting Y lock cylinder 5.36−1................................
5.37 Using the Digital Sequence Timer 5.37−1............................
5.37.1 Preparation 5.37−1.........................................................
5.37.2 Procedure 5.37−2..........................................................
5.38 Backlight Replacement on Main Control Panel 5.38−1.................
Replacing backlight 5.38−1..............................................
6. MAINTENANCE PRECISION CHECK 6.0−2.............
7.1 Checking Maintenance Precision 6.1−1..............................
7. MAINTENANCE GUIDE
(CONTROL) 7.0−2.................................
7.1 NC Unit Adjustment 7.1−1..........................................
7.1.1 Table Signal Connection Check 7.1−1.........................................
7.1.2 AC Servomotor Drivers Adjustment 7.1−2.....................................
SERVICE MANUAL
RH5
5
DA3SEC−02−020−B0
7.1.3 AC Motor Power ON 7.1−4..................................................
7.1.4 Manual Mode Movement Check in the Manual Mode 7.1−5......................
7.1.5 Semi−auto Mode Movement Check 7.1−6.....................................
7.1.6 Fine adjustments 7.1−8.....................................................
7.2 AC Servomotor Adjustment 7.2−1...................................
7.2.1 AC Motor Driver Check 7.2−1................................................
7.2.2 AC Motor Power ON 7.2−2..................................................
7.2.3 Manual Mode Movement Check 7.2−2........................................
7.2.4 Semi−auto Mode Movement Check 7.2−3.....................................
7.2.5 Setting/Browsing User Constant (Memory Switch) (Cn−01 and Cn−02) 7.2−18.......
8.3 Digital Operator 7.3−1.............................................
7.3.1 Inputting Offset Value (Cn−00) 7.3−1..........................................
7.3.2 Inputting Bit No. (Cn−01 and Cn−02) 7.3−3....................................
7.3.3 Changing Driver Setting Value (Cn−03 through Cn−23) 7.3−5....................
8. RELATED INFORMATION 8.0−2.......................
8.1 Construction Drawing List 8.1−1....................................
8.1.1 Construction Drawing List (NM−8244A/B/C) 8.1−1..............................
8.1.2 Construction Drawing List (NM−8245A/B/C) 8.1−3..............................
8.2 List of Software Settings 8.2−1.....................................
9.3 List of Jumper Switch Settings 8.3−1................................
8.3.1 CNC−4S (I) Board Setting 8.3−1.............................................
8.3.2 RCG Board Setting (X984 − 204) 8.3−8.......................................
8.3.3 RCG (I) Board Setting (X984 − 211) 8.3−13.....................................
8.3.4 MIOE (I) Board Setting 8.3−16................................................
8.3.5 SEQ−SE (I) Board Setting 8.3−31.............................................
8.3.6 APC Board Setting 8.3−34....................................................
9.4 AC Servomotor Drivers 8.4−1.......................................
8.4.1 X/Y/Z (40−, 62−feeder) and H (Camshaft) Axis Driver 8.4−1......................
8.4.2 Z Axis (80−feeder) Driver 8.4−8..............................................
8.5 Cycle Timer Setting 8.5−1..........................................
8.6 Checking Slow Down, Origin, Limit and Safety Limit Sensors 8.6−1.....
8.7 CNC Board Table Setting 8.7−1.....................................
8.8 Monitoring I/O Signals 8.8−1........................................
8.9 Measuring Belt Tension 8.9−1.......................................
8.9.1 Sonic Tension Meter 8.9−1..................................................
8.9.2 Main Drive Unit 8.9−3.......................................................
8.9.3 Z Axis Driver 8.9−5.........................................................
8.10 Removing Battery from Controller (Panadac 791) 8.10−1...............
8.11 Differences in Specifications between RHIII and RH5 8.11−1...........
RH5
SERVICE MANUAL
6
DA3SEC−02−020−B0
= MEMO =