JM-50使用说明书.pdf - 第7页

v 为了安全使用 JM -50 的注意事项注意 1. 为防止人身受伤，请勿在拆下安全盖（安全罩）、安全装置等状态下运行。 2. 为防止人身受伤，请务必小心，以免头发、衣服等被卷入传送带链。此外，请勿戴手套。 3. 为防止人身受伤，维护时（注油、调整、日常检修），请切断电源。 4. 为防止人身受伤，请在电源线上使用漏电断路器。 < 安全盖（安全罩） > 1 . 开关安全盖（安全罩）时请注意下列事…

各使用环节中的注意事项

使用环境

1. 为防止因误动作而引起的事故，请勿在受高频焊机等干扰源（电磁波）影响的环境下使用。

2. 为防止因误动作而引起的事故，请勿在超过使用电源电压±10％的情况下使用。

3. 为防止因误动作而引起的事故，请在 0.5±0.05MPa 的供气压力下使用。

4. 为了安全使用，请在下述环境下使用。

运行的环境条件温度：10℃～35℃

湿度：50％RH 以下 (无冷凝)

标高：1,000m 以下

5. 为防止电气部件破损引起的事故，从冷处将机器突然移动到暖处时，有时会结露，因此，请在完全

无需担心水滴后再接通电源。

6. 为防止电气部件破损而引起的事故，打雷时请停止使用，并拔出电源插头。

注意

为了安全使用

JM-50

的注意事项

注意

为防止人身受伤，请勿在拆下安全盖（安全罩）、安全装置等状态下运行。

2. 为防止人身受伤，请务必小心，以免头发、衣服等被卷入传送带链。

此外，请勿戴手套。

3. 为防止人身受伤，维护时（注油、调整、日常检修），请切断电源。

4. 为防止人身受伤，请在电源线上使用漏电断路器。

安全盖（安全罩）

1. 开关安全盖（安全罩）时请注意下列事项。

・打开安全盖（安全罩）时要把盖（罩）向上开足直到面向左侧的锁定臂处于“上

锁”状态后，再放开手。

没有上锁就放开手时，盖（罩）有落下来的危险。

・关闭盖（罩）子时先解开锁，再关闭盖（罩）子。

（请注意，解开锁时不要使盖（罩）子落下来导致受伤。）

・不要过渡增加盖（罩）子、手把等的负荷。

・如果 Head 单元位于主机装置后面，开关后侧安全盖（安全罩）时，可能会接触

到 X 轴单元。这时，请将 Head 单元移动到主机装置前面，再进行后侧安全盖

（安全罩）的开关。

注意

本装置的操作系统采用

Windows 7

（包括以太网通信功能）。

除安装提供的用于本装置的软件之外，加装其他软件，不保证正常运行。

对 SSD 内装入的文件进行转移、重命名、文件或文件夹的压缩、复制，也同样

不保证正常运行，敬请谅解。

●万一出现此种情况，可能需要更换新的

SSD

、丢失数据，务请格外注意。

注意

为保护操作系统，使用了

Enhanced Write Filter(EWF)

组件，进行了

盘

ROM

化。

1. 请勿在 C 盘保存文件。

把文件保存在 ROM 化后的 C 盘，会仿真占用主存储器。

因而，把文件存在 C 盘里时，会增加主存储器的使用量，压迫系统。

反复保存后可能造成内存不足，显示系统错误，可能需要重启本设备。

2. 需要修改操作系统的信息时，必须进行 C 盘的更新操作。

操作方法请参见使用说明书「1-10 更新 C 盘的操作」。

需要修改操作系统信息的操作是指下列事项：

・JM-50 系统软件的版本升级

・添加打印机

・设置网络（IP 地址、工作组等）

・添加用户

・变更资源管理器的设置

●要变更操作系统信息时，在执行 C 盘的更新操作后，需要重启一次本装置。

注意

本装置的

盘可用于安装软件或保存数据，但容量有限。

1：请确保 D 盘的可用空间。

D 盘的可用空间请确保 500MB 以上。

可用空间不足 500MB 时，请删除无用的文件(旧版本的主机软件、Log 文件、无

用的生产程序等），以确保可用空间。

●在可用空间不足的状态下使用时，可能发生应用软件错误或文件 I/O 错误，导致软

件运行不稳定，无法进行正常的动作。

注意

本装置在

ATX

电源中使用了电池，以保护停电时的生产程序等。

为防止 ATX 内置电池老化，请勿在非通电状态下将本装置放置 6 个月以上。

●本装置以主断路器及总开关

的状态为通电状态。

为了安全使用机器

第1 部基本篇　　　　　　　　　　　　　　　　　　　　　　　　　　　　

第1 章装置概要 ·········································································· 1-1

1-1 本装置概要 ···································································································· 1-1

1-1-1 前言 ···········································································································1-1

1-1-2 特长 ···········································································································1-2

1-1-3 特性 ···········································································································1-4

1-1-4 系统构成 ·····································································································1-6

1-1-5 缩写的说明 ··································································································1-8

1-1-6 本装置的构成 ·······························································································1-9

1-2 本装置的构造 ······························································································· 1-11

1-2-1 基板传送部分的构造 ···················································································· 1-11

1-2-2 元件供给部分的构成 ···················································································· 1-12

1-2-3 Head 单元的构成 ························································································· 1-15

1-2-4 R-ATC 单元的构成 ······················································································· 1-18

1-2-5 图像识别装置(3D 传感器)的构成 ····································································· 1-22

1-3 机械规格 ····································································································· 1-23

1-3-1 机械尺寸与重量 ·························································································· 1-23

1-3-2 贴片精度 ··································································································· 1-24

1-3-3 其他 ········································································································· 1-25

1-3-4 X, Y, Z, ZA, θ 轴的说明 ·················································································· 1-26

1-4 电气规格 ····································································································· 1-27

1-4-1 与外部装置的接口 ······················································································· 1-28

1-4-2 电源缆线的连接 ·························································································· 1-30

1-5 对象元件及元件包装方式 ················································································ 1-31

1-6 印刷基板规格 ······························································································· 1-35

1-7 定心系统 ····································································································· 1-39

1-8 基本操作 ····································································································· 1-44

1-8-1 画面构成示例 ····························································································· 1-44

1-8-2 显示装置及输入装置 ···················································································· 1-45

1-8-3 操作方法 ··································································································· 1-47

1-8-4 菜单、功能按钮 ·························································································· 1-52

1-8-5 简易事项显示画面 ······················································································· 1-62

1-9 文件的操作 ·································································································· 1-64

1-9-1 新建 ········································································································· 1-64

1-9-2 打开（读入文件） ······················································································· 1-64

1-9-3 保存 ········································································································· 1-65

1-9-4 另存为 ······································································································ 1-66

1-9-5 文本文件输出 ····························································································· 1-68

1-9-6 设备信息的取得和保存 ················································································· 1-71

1-9-7 保存图像数据 ····························································································· 1-77

1-9-8 生产程序初始文件夹 ···················································································· 1-78

1-9-9 文件管理 ··································································································· 1-79

1-9-10 硬件安全拆卸 ···························································································· 1-80

1-10 C 盘的更新操作 ··························································································· 1-81