XP-142E System Reference-SYS-XP142-2.0E.pdf.pdf - 第184页

Part 3 Chapter 3 Editor Edition 2.0 3-3-29 XP-142E System Reference Element An “element” is a group of uniform, constant-pitch leads. Because a part body may comprise several elements, each of these elements is assigned …

Part 3 Chapter 3 Editor

Edition 2.0 3-3-28 XP-142E System Reference

Part Height

Specifies the part height (thickness from nozzle pick-up face to part’s bottom face). The

height includes the lead length. (0.01 mm ~ 6.0 mm)

(Refer to the illustration below. The “Pickup Point Offset Z” and “Placing Offset Z”

items are explained later in this manual.)

* The top face of the tape and tray is the pickup reference position.

* Z-axis height at pickups:

(For tape) Pickup position reference + Pickup Point Offset Z

(For tray) Pickup position reference + Tray Pick Offset Z

Lead

Pitch Tolerance

Specifies the lead pitch tolerance range. (0% to 100%)

Vision Type 100 is supported. A setting of “0%” is processed as “30%”.

Measure Point of Lead

Specifies the position where vision processing is to occur as a percentage of the total lead

length, measured from the lead tip. If “0” is entered, then vision processing occurs at the

position on the lead 20% of the total lead length from the lead tip. This setting is only

used with vision types 20 and 100. (0 – 100%)

Pickup position reference

Pickup Point Offset Z origin

Tray Pick Offset Z origin

Pickup Point

Offset Z

(for feeder)

Tray Pick

Offset Z

(for tray)

Part Height

MCSX330Ea

Part 3 Chapter 3 Editor

Edition 2.0 3-3-29 XP-142E System Reference

Element

An “element” is a group of uniform, constant-pitch leads. Because a part body may

comprise several elements, each of these elements is assigned a number to distinguish

between them. Element data includes the lead length, width and pitch.

Operation Button Explanations

Closes the dedicated element data editor and returns to the part data

editor.

The following buttons apply to the line which has been selected in the selection area at

the left side of the screen.

Copies the selected line to the clipboard.

Pastes the clipboard data above the selected line.

Deletes the selected line, and moves the subsequent lines up to fill the

vacated space.

Inserts a new (blank) line above the selected line.

Cancels all selections.

XP2S2210Ea

Specify new data

Select area

Insert

Paste

Setting Item Explanations

Side

Specify the body side where the element is located.

Position X, Position Y

Specify the X/Y direction position of the element center, as measured from the body

center. (-99.99 mm ~ 99.99 mm)

Lead Quantity

Specifies the number of leads in the element. (0 ~ 128)

Lead Pitch

Specifies the pitch between the leads. (0.000 mm ~ 99.999 mm)

Lead Width

Specifies the lead width. (0.000 mm ~ 99.999 mm)

Lead Length

Specifies the lead length. (0.000 mm ~ 99.999 mm)

Lead Width Tolerance (Presently not supported)

Specifies the lead width tolerance. (0.000 mm ~ 99.999 mm)

Lead Length Tolerance

Specifies the lead length tolerance. (0.000 mm ~ 99.999 mm)

If a setting of “0” is entered, the lead length tolerance will automatically be set as 30 % of

the lead length. This setting is only used with vision type 100.

Lead Center Tolerance

Enter the lead’s bend tolerance. (0.000mm ~ 99.999mm)

If a setting of “0” is entered, the lead center tolerance will automatically be set as 30% of

the lead length. This setting is only used with vision type 100.

P Pattern

This data defines how the lead image is viewed. (0 ~ 255)

When using Vision Type 100 (QF & Connector: Frontlight processing), enter a setting of

“14”. If the lead is dark and the background is light, enter a setting of “13”.

Lead element

MCSX333Ea

(PositionX, PositionY)

(0, 0)

Part 3 Chapter 3 Editor

Edition 2.0 3-3-30 XP-142E System Reference