XP-142E System Reference-SYS-XP142-2.0E.pdf.pdf - 第340页
4. The CYCLE ST OP Button 4.1 During production, the machine does not stop when CYCLE STOP is pushed. Symptoms: During production, the machine does not stop when CYCLE STOP is pushed. Remedy: The following pushbutton swi…
3. The READY ON and START Buttons
3.1 After pushing READY ON, the machine moves even though
START has not been pushed.
Symptoms: At the [Production] - [Automatic] screen, the READY ON button is pushed,
and the machine moves before the START button is pushed.
At the [Manual Operation] commands, the machine moves although the
START button has not been pushed.
Remedy: The following pushbutton switch may be malfunctioning. Contact a Fuji
Machine dealer for assistance.
X000: StartButton: Start PB
3.2 The START button does not respond even though “Push the
START switch” appears on screen.
Symptoms: When using the [Production] or [Manual Operation] screens, the START
button does not respond even though the message, “Push the START
switch,” appears on screen.
Remedy: The following pushbutton switch may be malfunctioning. Contact a Fuji
Machine dealer for assistance.
X000: StartButton: Start PB
3.3 The servo power turns on when the machine is ready, even
though the READY ON button has not been pushed.
Symptoms: When the start conditions are fulfilled (safety covers are closed, the
EMERGENCY STOP is released, etc.), the servo power turns on even though
the READY ON button has not been pushed.
The READY ON button is flashing when this happens.
Remedy: The following pushbutton switch may be malfunctioning. Contact a Fuji
Machine dealer for assistance.
X001: ReadyOnButton: READY ON PB
3.4 The servo power does not turn on when the machine is ready
and READY ON is pushed.
Symptoms: When the start conditions are fulfilled (safety covers are closed, the
EMERGENCY STOP is released, etc.) and the READY ON button is pushed,
the servo power does not turn on.
The READY ON button flashes normally.
Remedy: The following pushbutton switch may be malfunctioning. Contact a Fuji
Machine dealer for assistance.
X001: ReadyOnButton: READY ON PB
3.5 The READY ON button lights up but the START button does not
flash.
Symptoms: The start conditions are fulfilled and the READY ON button lights up when
pushed, but the START button does not flash.
Remedy: The following pushbutton switch may be malfunctioning. Contact a Fuji
Machine dealer for assistance.
X007: CycleStopBtn: Cycle stop PB
Part 8 Chapter 3 Corrective Measures for Problems at the Machine
Edition 2.0 8-3-3 XP-142E System Reference
4. The CYCLE STOP Button
4.1 During production, the machine does not stop when CYCLE
STOP is pushed.
Symptoms: During production, the machine does not stop when CYCLE STOP is
pushed.
Remedy: The following pushbutton switch may be malfunctioning. Contact a Fuji
Machine dealer for assistance.
X007: CycleStopBtn: Cycle stop PB
5. Panel Loading and Unloading
5.1 Production starts when before a panel arrives at the main station
Symptoms: Production starts when there is no panel at the main station, and error code
14011000 (fiducial mark read error) appears on screen.
Remedy: The following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X01D: MainStArriveChk: MAIN station panel arrival check
5.2 When loading a panel, the panel stops before arrival at the main
station.
Symptoms: When loading a panel, the panel stops before arrival at the main station.
Remedy: The following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X024: MainStLftUpChk: MAIN station lifter up limit check
5.3 When loading a panel, the panel does not decelerate before
arrival at the main station.
Symptoms: When loading a panel, the panel does not decelerate before arrival at the
main station. Then the machine begins production.
Remedy: The following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X01C: MainStDecelPnt: MAIN station panel deceleration start point
5.4 Error code 1503100E (Failed to convey panel) is displayed during
panel loading.
Symptoms: Error code 1503100E (Failed to convey panel) is displayed during panel
loading.
Remedy: If the remedy listed with the error code does not correct the problem, then
the following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X01C: MainStDecelPnt: MAIN station panel deceleration start point
5.5 Error code 15032011 (Failed to convey panel) is displayed during
panel loading.
Symptoms: Error code 15032011 (Failed to convey panel) is displayed during panel
loading.
Remedy: If the remedy listed with the error code does not correct the problem, then
the following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X022: MainStPassChk: MAIN station panel pass check
Part 8 Chapter 3 Corrective Measures for Problems at the Machine
Edition 2.0 8-3-4 XP-142E System Reference
5.6 When finished producing a panel, the machine unloads the panel
prematurely, before the next machine issues a panel request
signal.
Symptoms: When finished producing a panel, the machine unloads the panel, even
though the next machine still has a panel.
Remedy: The following input connection may be malfunctioning or grounded.
Contact a Fuji Machine dealer for assistance.
X019: PcbRequest: Panel request signal from next machine
5.7 When finished with production, the machine does not unload the
panel to the next machine.
Symptoms: When finished with production, the machine does not unload the panel to
the next machine.
The machine may not stop even when the CYCLE STOP button is pushed.
Remedy: The following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X01C: MainStDecelPnt: MAIN station panel deceleration start point
Also, the following input may be malfunctioning or the signal may not be
arriving at the next machine. Contact a Fuji Machine dealer for assistance.
X019: PcbRequest: Panel request signal from next machine
5.8 Error code 15031010 (Failed to convey panel) is displayed during
panel unloading.
Symptoms: Error code 15031010 (Failed to convey panel) is displayed during panel
unloading.
Remedy: If the remedy listed with the error code does not correct the problem, then
the following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X022: MainStPassChk: MAIN station panel pass check
6. MFU
6.1 The machine cannot clamp or unclamp the MFU
Symptoms: The machine will not clamp/unclamp the MFU. The following messages
appear.
When clamped: Failed to raise the MFU.
When unclamped: Failed to lower the MFU.
Remedy: Check for any obstacles blocking the movement of the MFU. If nothing is
blocking the MFU, then one of the following sensors may be
malfunctioning. Contact a Fuji Machine dealer for assistance.
(Side 1)
X02E: Side1MfuUpChk: MFU UP limit check (side 1)
X02F: Side1MfuDwnChk: MFU DOWN limit check (side 1)
X03A: Side1MfuChk: MFU check (side 1)
(For machines with MFUs on side 1 and 2)
X02D: Side1MfuConChk: MFU connect check (side 1)
(For machines with trays on side 2)
(Side 2)
X03E: Side2MfuUpChk: MFU UP limit check (side 2)
X03F: Side2MfuDwnChk: MFU DOWN limit check (side 2)
X03B: Side2MfuChk: MFU check (side 2)
Part 8 Chapter 3 Corrective Measures for Problems at the Machine
Edition 2.0 8-3-5 XP-142E System Reference