XP-142E System Reference-SYS-XP142-2.0E.pdf.pdf - 第309页

Code: 120501BB Display: Unable to retract the shuttle. A retracted tray already exists. Confirm the tray pallet position. Close this error message and input the current tray slot number in the displayed dialog. Cause: An…

Code: 120501B2

Display: Reset cylinder movement error.

Cause: The reset cylinder up or down movement has not been confirmed.

Remedy: Check the reset cylinder raised confirmation sensor.

The nozzle piston may be locked.

Push down on the nozzle piston to check its vertical movement.

Code: 120501B3

Display: Backup pin interference sensor activated.

Cause: Backup pin interference sensor activated.

Remedy: Correct the position of the backup pin.

Check the backup pin interference sensor is functioning correctly.

Code: 120501B4

Display: A thermal abnormality has occurred. Check the following item.

Cause: A thermal abnormality was detected.

Remedy: Check the X- and Y-axis regenerative resistance temperature fuse and vacuum

pump temperature fuse functions (XP-141, XP-142). Check the motor thermal

relay for the vacuum pump (XP-141, XP-142).

Code: 120501B6

Display: Limit over (Pick-up position)

Cause: Limit over (Pick-up position).

Remedy: Check the corrected pick-up value and pick-up point offset.

Code: 120501B7

Display: Limit over (Pick-up position)

Cause: Z limit over (Pick-up position)

Remedy: Check the pick-up point offset Z.

Code: 120501B8

Display: An empty tray dropped during tray ejection.

Cause: The tray pick-up sensor switched OFF during tray ejection.

Remedy: Remove the empty tray from the interior of the machine.

Code: 120501B9

Display: The pick-up measurement position exceeds the servo limit.

Cause: The pick-up measurement position exceeds the servo limit.

Remedy: Check that the servo limit specified in the calibration data is correct.

If the servo limit is correct, machine modifications are required to extend the servo

limit, making measurement possible.

For machines that have not been modified, disable this function by setting the

calibration data item “_PickPosAutoMeasure” to “0”.

Code: 120501BA

Display: Unable to advance the shuttle.

An advanced tray already exists.

Confirm the tray pallet position.

Cause: An advanced tray already exists.

The shuttle cannot advance because the tray advance position sensor is OFF.

Remedy: Confirm the tray pallet position.

Check the tray advance position sensor is functioning correctly.

Part 8 Chapter 1 Error Code Messages and Corrective Measures

Edition 2.0 8-1-20 XP-142E System Reference

Code: 120501BB

Display: Unable to retract the shuttle.

A retracted tray already exists.

Confirm the tray pallet position.

Close this error message and input the current tray slot number in the displayed

dialog.

Cause: An attempt was made to retract the shuttle, however, the tray pallet is already

retracted.

Remedy: Confirm the tray pallet position.

Check the tray advance position and tray retract position sensors are functioning

correctly.

Close this error message and input the current tray slot number in the displayed

dialog.

Code: 120501BC

Display: The tray pusher cannot be advanced.

Confirm the tray pusher position.

Cause: An attempt was made to advance the tray pusher, however the tray pusher retract

sensor did not turn off within the required time period.

Remedy: Confirm the tray pusher position.

Check that the tray pusher advance and retract confirmation sensors are

functioning correctly.

Code: 120501BD

Display: The tray pusher cannot be advanced.

Confirm the tray pusher position.

Cause: An attempt was made to retract the tray pusher after it advanced, however the

tray pusher advance confirmation sensor did not turn on within the required time

period.

Remedy: Confirm the tray pusher position.

Check that the tray pusher advance and retract confirmation sensors are

functioning correctly.

Code: 120501BE

Display: The tray pusher cannot be retracted.

Confirm the tray pusher position.

Cause: An attempt was made to retract the tray pusher, however the tray pusher advance

confirmation sensor remained ON for the required time period.

Remedy: Confirm the tray pusher position.

Check that the tray pusher advance and retract confirmation sensors are

functioning correctly.

Code: 120501BF

Display: The tray pusher cannot be retracted.

Confirm the tray pusher position.

Cause: An attempt was made to retract the tray pusher, however, after the tray pusher

advance sensor turned OFF, the tray pusher retract confirmation sensor remained

OFF for the required time period.

Remedy: Confirm the tray pusher position.

Check that the tray pusher retract and advance confirmation sensors are

functioning correctly.

Part 8 Chapter 1 Error Codes and Corrective Measures

Edition 2.0 8-1-21 XP-142E System Reference

Code: 120501C0

Display: The tray shutter is open.

Cause: The tray shutter open sensor is OFF.

Remedy: Check that the tray shutter is closed.

Check that the tray shutter position sensor is functioning correctly.

Code: 120501C1

Display: The tray shuttle is not at the origin position.

The elevator cannot be moved.

Confirm the tray shuttle position.

Cause: Because the tray shuttle is not at the origin position the tray cannot be moved on

the elevator.

Remedy: Confirm the tray shuttle position.

Check that the tray shuttle position sensor is functioning correctly.

Code: 120501C2

Display: The tray shuttle position confirmation sensor turned off while the elevator was

moving.

The elevator cannot be moved.

Confirm the tray shuttle position.

Cause: The magazine tray check sensor turned off while the elevator was moving.

Remedy: Confirm the tray shuttle position.

Check that the tray shuttle position sensor is functioning correctly.

Code: 120501C3

Display: The U-axis interlock sensor is blocked.

Cause: The U-axis interlock sensor was blocked while the shuttle was moving.

Remedy: Check that nothing is on top of the tray pallet.

Check that the U-axis interlock sensor is functioning correctly.

Code: 120501C4

Display: Tray parts cannot be picked up from the specified slot. Reduce the number of

trays.

Cause: Tray parts cannot be picked up from the specified slot.

Remedy: Reduce the number of trays.

Code: 120501C5

Display: The head cannot pass over a tray when picking up adjacent tray parts as the tray

height for the specified slot is too high. Reduce the number of trays.

Cause: The head cannot pass over a tray when picking up adjacent tray parts as the tray

height for the specified slot is too high.

Remedy: Reduce the number of trays.

Code: 120501C6

Display: The head cannot pass over a tray when ejecting the specified tray. Reduce the

number of trays.

Cause: The head cannot pass over a tray when ejecting the specified tray.

Remedy: Reduce the number of trays.

Part 8 Chapter 1 Error Code Messages and Corrective Measures

Edition 2.0 8-1-22 XP-142E System Reference