XP-142E System Reference-SYS-XP142-2.0E.pdf.pdf - 第342页
7. T ape Cutter 7.1 The tape cutter will not move Symptoms: The tape cutter will not move properly. No error message is displayed. Remedy: Check for any obstacles blocking the movement of the tape cutter. If nothing is b…
5.6 When finished producing a panel, the machine unloads the panel
prematurely, before the next machine issues a panel request
signal.
Symptoms: When finished producing a panel, the machine unloads the panel, even
though the next machine still has a panel.
Remedy: The following input connection may be malfunctioning or grounded.
Contact a Fuji Machine dealer for assistance.
X019: PcbRequest: Panel request signal from next machine
5.7 When finished with production, the machine does not unload the
panel to the next machine.
Symptoms: When finished with production, the machine does not unload the panel to
the next machine.
The machine may not stop even when the CYCLE STOP button is pushed.
Remedy: The following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X01C: MainStDecelPnt: MAIN station panel deceleration start point
Also, the following input may be malfunctioning or the signal may not be
arriving at the next machine. Contact a Fuji Machine dealer for assistance.
X019: PcbRequest: Panel request signal from next machine
5.8 Error code 15031010 (Failed to convey panel) is displayed during
panel unloading.
Symptoms: Error code 15031010 (Failed to convey panel) is displayed during panel
unloading.
Remedy: If the remedy listed with the error code does not correct the problem, then
the following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X022: MainStPassChk: MAIN station panel pass check
6. MFU
6.1 The machine cannot clamp or unclamp the MFU
Symptoms: The machine will not clamp/unclamp the MFU. The following messages
appear.
When clamped: Failed to raise the MFU.
When unclamped: Failed to lower the MFU.
Remedy: Check for any obstacles blocking the movement of the MFU. If nothing is
blocking the MFU, then one of the following sensors may be
malfunctioning. Contact a Fuji Machine dealer for assistance.
(Side 1)
X02E: Side1MfuUpChk: MFU UP limit check (side 1)
X02F: Side1MfuDwnChk: MFU DOWN limit check (side 1)
X03A: Side1MfuChk: MFU check (side 1)
(For machines with MFUs on side 1 and 2)
X02D: Side1MfuConChk: MFU connect check (side 1)
(For machines with trays on side 2)
(Side 2)
X03E: Side2MfuUpChk: MFU UP limit check (side 2)
X03F: Side2MfuDwnChk: MFU DOWN limit check (side 2)
X03B: Side2MfuChk: MFU check (side 2)
Part 8 Chapter 3 Corrective Measures for Problems at the Machine
Edition 2.0 8-3-5 XP-142E System Reference
7. Tape Cutter
7.1 The tape cutter will not move
Symptoms: The tape cutter will not move properly. No error message is displayed.
Remedy: Check for any obstacles blocking the movement of the tape cutter. If
nothing is blocking the cutter, then one of the following sensors may be
malfunctioning. Contact a Fuji Machine dealer for assistance.
X030: Side1TpCutFwdEnd: Tape cutter forward end check (side 1)
(XP-142E)
X049: Side1TpCutFwdEnd: Tape cutter forward end check (side 1)
(XP-242E)
Part 8 Chapter 3 Corrective Measures for Problems at the Machine
Edition 2.0 8-3-6 XP-142E System Reference
XP-142E System Reference
Edition Date Compatible software version
Edition 1.0 June 23, 2003 V1.00
Edition 2.0 January 30, 2004 V2.00
FUJI Machine Manufacturing Co., Ltd.
SMT Equipment
19 Chausuyama, Yamamachi, Chiryu,
Aichi Prefecture, 472-8686 Japan
Copyright 2004 by Fuji Machine Manufacturing Co., Ltd.
Printed in Japan
FUJI Internet
Fuji Internet aims at providing up-to-date information to our
customers in the most efficient manner. This site makes a range
of services available, from manual updates and virtual training,
to online technical reports. Fuji hopes that this site will be used
as a source of information in addition to the services provided
by your agent.
Fuji internet is located at http://www.fuji.co.jp/
Fuji Internet membership is required to access the Technical
Information section of the site. Please contact your agent for
membership details.
Any comments or opinions regarding this document can be sent
to intnetqst@fuji.co.jp