XP-142E System Reference-SYS-XP142-2.0E.pdf.pdf - 第341页
5.6 When finished producing a panel, the machine unloads the panel prematurely , before the next machine issues a panel request signal. Symptoms: When finished producing a panel, the machine unloads the panel, even thoug…
4. The CYCLE STOP Button
4.1 During production, the machine does not stop when CYCLE
STOP is pushed.
Symptoms: During production, the machine does not stop when CYCLE STOP is
pushed.
Remedy: The following pushbutton switch may be malfunctioning. Contact a Fuji
Machine dealer for assistance.
X007: CycleStopBtn: Cycle stop PB
5. Panel Loading and Unloading
5.1 Production starts when before a panel arrives at the main station
Symptoms: Production starts when there is no panel at the main station, and error code
14011000 (fiducial mark read error) appears on screen.
Remedy: The following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X01D: MainStArriveChk: MAIN station panel arrival check
5.2 When loading a panel, the panel stops before arrival at the main
station.
Symptoms: When loading a panel, the panel stops before arrival at the main station.
Remedy: The following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X024: MainStLftUpChk: MAIN station lifter up limit check
5.3 When loading a panel, the panel does not decelerate before
arrival at the main station.
Symptoms: When loading a panel, the panel does not decelerate before arrival at the
main station. Then the machine begins production.
Remedy: The following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X01C: MainStDecelPnt: MAIN station panel deceleration start point
5.4 Error code 1503100E (Failed to convey panel) is displayed during
panel loading.
Symptoms: Error code 1503100E (Failed to convey panel) is displayed during panel
loading.
Remedy: If the remedy listed with the error code does not correct the problem, then
the following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X01C: MainStDecelPnt: MAIN station panel deceleration start point
5.5 Error code 15032011 (Failed to convey panel) is displayed during
panel loading.
Symptoms: Error code 15032011 (Failed to convey panel) is displayed during panel
loading.
Remedy: If the remedy listed with the error code does not correct the problem, then
the following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X022: MainStPassChk: MAIN station panel pass check
Part 8 Chapter 3 Corrective Measures for Problems at the Machine
Edition 2.0 8-3-4 XP-142E System Reference
5.6 When finished producing a panel, the machine unloads the panel
prematurely, before the next machine issues a panel request
signal.
Symptoms: When finished producing a panel, the machine unloads the panel, even
though the next machine still has a panel.
Remedy: The following input connection may be malfunctioning or grounded.
Contact a Fuji Machine dealer for assistance.
X019: PcbRequest: Panel request signal from next machine
5.7 When finished with production, the machine does not unload the
panel to the next machine.
Symptoms: When finished with production, the machine does not unload the panel to
the next machine.
The machine may not stop even when the CYCLE STOP button is pushed.
Remedy: The following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X01C: MainStDecelPnt: MAIN station panel deceleration start point
Also, the following input may be malfunctioning or the signal may not be
arriving at the next machine. Contact a Fuji Machine dealer for assistance.
X019: PcbRequest: Panel request signal from next machine
5.8 Error code 15031010 (Failed to convey panel) is displayed during
panel unloading.
Symptoms: Error code 15031010 (Failed to convey panel) is displayed during panel
unloading.
Remedy: If the remedy listed with the error code does not correct the problem, then
the following sensor may be malfunctioning. Contact a Fuji Machine dealer
for assistance.
X022: MainStPassChk: MAIN station panel pass check
6. MFU
6.1 The machine cannot clamp or unclamp the MFU
Symptoms: The machine will not clamp/unclamp the MFU. The following messages
appear.
When clamped: Failed to raise the MFU.
When unclamped: Failed to lower the MFU.
Remedy: Check for any obstacles blocking the movement of the MFU. If nothing is
blocking the MFU, then one of the following sensors may be
malfunctioning. Contact a Fuji Machine dealer for assistance.
(Side 1)
X02E: Side1MfuUpChk: MFU UP limit check (side 1)
X02F: Side1MfuDwnChk: MFU DOWN limit check (side 1)
X03A: Side1MfuChk: MFU check (side 1)
(For machines with MFUs on side 1 and 2)
X02D: Side1MfuConChk: MFU connect check (side 1)
(For machines with trays on side 2)
(Side 2)
X03E: Side2MfuUpChk: MFU UP limit check (side 2)
X03F: Side2MfuDwnChk: MFU DOWN limit check (side 2)
X03B: Side2MfuChk: MFU check (side 2)
Part 8 Chapter 3 Corrective Measures for Problems at the Machine
Edition 2.0 8-3-5 XP-142E System Reference
7. Tape Cutter
7.1 The tape cutter will not move
Symptoms: The tape cutter will not move properly. No error message is displayed.
Remedy: Check for any obstacles blocking the movement of the tape cutter. If
nothing is blocking the cutter, then one of the following sensors may be
malfunctioning. Contact a Fuji Machine dealer for assistance.
X030: Side1TpCutFwdEnd: Tape cutter forward end check (side 1)
(XP-142E)
X049: Side1TpCutFwdEnd: Tape cutter forward end check (side 1)
(XP-242E)
Part 8 Chapter 3 Corrective Measures for Problems at the Machine
Edition 2.0 8-3-6 XP-142E System Reference