XP-142E System Reference-SYS-XP142-2.0E.pdf.pdf - 第321页
Code: 12056038 Display: Nozzle size check error An error occurred when performing nozzle size check by sensor. Check that the machine nozzles match the nozzle settings in the data editor. Check the operation of the nozzl…
Code: 12056033
Display: The remover is interfering with the tray positioning plate when ejecting the tray.
Change the [Tray Dump Pick Position X] setting in part data so that the remover
does not extend beyond the tray.
Cause: The remover interferes with the tray positioning plate when picking up the empty
tray.
Remedy: Change the [Tray Dump Pick Position X] setting in part data so that the remover
does not extend beyond the tray.
Code: 12056034
Display: The remover is interfering with the tray positioning plate when ejecting the tray.
Change the [Tray Dump Pick Position Y] setting in part data so that the remover
does not extend beyond the tray.
Cause: The remover interferes with the tray positioning plate when picking up the empty
tray.
Remedy: Change the [Tray Dump Pick Position Y] setting in part data so that the remover
does not extend beyond the tray.
Code: 12056035
Display: The nozzle interferes with the tray positioning plate when picking up parts.
(At the front side of the tray as seen from the front of the machine.)
Cause: The nozzle interferes with the tray positioning plate when picking up parts.
(At the front side of the tray as seen from the front of the machine.)
Remedy: Change the [Tray First Pickup Position Y] setting in the part data, or change one of
the following settings (as applicable) so that nozzles do not interfere with the tray
positioning plate.
*If [Direction] is set to 1 or 3, change the [Pick-up Point Offset X] setting.
*If [Direction] is set to 0 or 2, change the [Pick-up Point Offset Y] setting.
Code: 12056036
Display: The nozzle interferes with the tray positioning plate when picking up parts.
(The right side of the tray as seen from the front of the machine.)
Cause: The nozzle interferes with the tray positioning plate when picking up parts.
(The right side of the tray as seen from the front of the machine.)
Remedy: Change the [Tray First Pickup Position X] setting in the part data, or change one of
the following settings (as applicable) so that nozzles do not interfere with the tray
positioning plate.
*If [Direction] is set to 1 or 3, change the [Pick-up Point Offset Y] setting.
Code: 12056037
Display: The nozzle interferes with the tray positioning plate when picking up parts.
(The left side of the tray as seen from the front of the machine.)
Cause: The nozzle interferes with the tray positioning plate when picking up parts.
(The left side of the tray as seen from the front of the machine.)
Remedy: Change the [Tray First Pickup Position X] setting in the part data, or change one of
the following settings (as applicable) so that nozzles do not interfere with the tray
positioning plate.
*If [Direction] is set to 0 or 2, change the [Pick-up Point Offset X] setting.
*If [Direction] is set to 1 or 4, change the [Pick-up Point Offset Y] setting.
Part 8 Chapter 1 Error Code Messages and Corrective Measures
Edition 2.0 8-1-32 XP-142E System Reference
Code: 12056038
Display: Nozzle size check error
An error occurred when performing nozzle size check by sensor.
Check that the machine nozzles match the nozzle settings in the data editor.
Check the operation of the nozzle size check sensor.
Cause: An error occurred when performing nozzle size check by sensor.
Remedy: Check that the machine nozzles match the nozzle settings in the data editor.
Check the operation of the nozzle size check sensor.
Code: 12056150
Display: Tray pallet is not retracted.
The elevator cannot be moved.
Confirm the tray pallet position.
Cause: The tray cannot be moved on the elevator because the tray retract confirmation
sensor is OFF.
Remedy: Correct the tray shuttle and tray pallet positions.
Check that the tray retract confirmation sensor is functioning correctly.
Code: 12056151
Display: The magazine tray check sensor turned off while the elevator was moving.
The elevator cannot be moved.
Confirm the tray pallet position.
Cause: The magazine tray check sensor turned off while the elevator was moving.
Remedy: Correct tray shuttle and tray pallet positions.
Check that the magazine tray check sensor is functioning correctly.
Code: 12100081
Display: Vision processing System Error
Cause: Vision processing System Error
Remedy: Internal error. This error should not occur under normal circumstances. Take a
machine trace and send it to your Fuji representative.
Code: 12100082
Display: Vision processing System Error
Cause: Vision processing System Error
Remedy: Internal error. This error should not occur under normal circumstances. Take a
machine trace and send it to your Fuji representative.
Code: 12100083
Display: Unable to detect leads.
Cause: Standard template error
Remedy: Check that the part data is correct; in particular, check the element data and the
“Stand Off” setting.
If the part data is correct, check the following possible causes:
*Poor pick-up performance
*Image brightness deterioration
*Poor camera focus
*Presence of dirt or other foreign object
Part 8 Chapter 1 Error Codes and Corrective Measures
Edition 2.0 8-1-33 XP-142E System Reference
Code: 12100084
Display: Element leads are more than the specified value
Cause: Element leads are more than the specified value
Remedy: Replace the parts for which the error occurred or check the part data is correct. If
the part data is correct, check the part pick-up condition is not incorrect. Check
the vision processing light brightness is functioning correctly, the focus is adjusted
correctly and the image is not dirty.
Code: 12100085
Display: Element leads are less than the specified value
Cause: Element leads are less than the specified value.
Remedy: Replace the parts for which the error occurred or check the part data is correct. If
the part data is correct, check the part pick-up condition is not incorrect. Check
the vision processing light brightness is functioning correctly, the focus is adjusted
correctly and the image is not dirty.
Code: 12100088
Display: Coplanarity tolerence error
Cause: The coplanarity check result shows the lead bent over the specified limit.
Remedy: Check the part lead is not bent or check the Coplanarity Tolerance specified in part
data is not too small.
Code: 12300301
Display: Socket transmission error
Cause: Unable to obtain a data communication port number at the IJ process or sub-
machine.
Remedy: Check the data communication port numbers for the IJ process and sub-machine
match.
Code: 12300302
Display: Socket transmission error
Cause: Unable to open the port because the designated port is not usable/in use.
Remedy: Check the communication port numbers for the IJ process and intermediate
machines match.
Code: 12300303
Display: Socket transmission error
Cause: The communication port number is invalid.
Remedy: Check that the communication port numbers for the IJ process and intermediate
machines match.
Code: 12300304
Display: Socket transmission error
Cause: Unable to obtain memory for socket communication.
Remedy: Internal error. This error should not occur under normal circumstances. Take a
machine trace and send it to your Fuji representative.
Code: 12300305
Display: Socket transmission error
Cause: The IP address is invalid.
Remedy: Check connecting terminal IP address of (IJ process or machine in the group).
Part 8 Chapter 1 Error Code Messages and Corrective Measures
Edition 2.0 8-1-34 XP-142E System Reference