XP-142E System Reference-SYS-XP142-2.0E.pdf.pdf - 第288页

Part 8 Errors and Countermeasures (ESR09AA) This chapter provides a list of the error codes that appear on the scr een when a machine error occurs, along with measures that can be taken to correct the err or . 1. Error C…

Address Display Description

Y020

Y021

Y022 GaugeChipVacuum Gauge chip vacuum

Y023

Y024 PcbRequest Panel request to previous machine

Y025 PcbAvailable Panel unloading enabled signal to next machine

Y026 FollowPermit Follow permit output

Y027

Y028 MainStLifterUp MAIN station UP

Y029 MainStLifterDown MAIN station DOWN

Y02A MainStationStp MAIN station stopper on

Y02B

Y02C

Y02D InStLifterUp IN station lifter UP

Y02E ConvMtrDec Conveyor motor deceleration command

Y02F Conv/WidthMtr Conveyor/Width change motor

Y030

Y031

Y032

Y033

Y034 Fluores.LampOn Fluorescent lamp on

Y035 ChgConv/Width Conveyor width change

Y036 ChgCw/Ccw Change motor direction

Y037 PcbVacuum Panel pick-up vacuum

Y038 Side1MfuDown MFU DOWN (Side 1)

Y039 Side1MfuUp MFU UP (Side 1)

Y03A Side1TapeCutFwd Tape cut forward (Side 1)

Y03B Side1TapeCutBwd Tape cut backward (Side 1)

Y03C Side2MfuDown MFU DOWN (Side 2)

Y03D Side2MfuUp MFU UP (Side 2)

Y03E Side2TapeCutFwd Tape cut forward (Side 2)

Y03F Side2TapeCutBwd Tape cut backward (Side 2)

Part 7 Chapter 2 System Output Signals

Edition 2.0 7-2-2 XP-142E System Reference

Part 8

Errors and

Countermeasures

(ESR09AA)

This chapter provides a list of the

error codes that appear on the screen

when a machine error occurs, along

with measures that can be taken to

correct the error.

1. Error Code Messages and Corrective Measures

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1-1

2. Corrective Measures for Error Messages that

Appear without an Error Code . . . . . . . . . .8-2-1

3. Corrective Measures for Problems at the

Machine

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3-1

1. Error Code Messages and Corrective Measures

(ESR0901)

The following is a list of the error messages that appear with error codes.

If an error message appears without a code (number), refer to Section 2, “Corrective Measures

for Error Messages that Appear without an Error Code”.

All error codes are 8 characters in length (Ex. 1101B000, 1101B001)

The error codes are listed in ascending order of code number.

Code: 1101B000

Display: [***] is a range error.

Cause: A value which exceeds the permissible input range was entered.

Remedy: Enter a value within the permissible input range.

Code: 1101B001

Display: [***] is not defined.

Cause: If the set items are values, enter 0, if they are characters leave the fields blank.

Remedy: Input valid values.

Code: 1101C700

Display: Feeder skip settings of “0” and “1” have both been specified in the sequence data

for the same stage and slot number.

Cause: Sequence data with and without feeder skip settings exist for the same stage/slot

number.

Remedy: Correct the sequence data so that all sequences for the same stage/slot number

have the same feeder skip settings.

Code: 1101C701

Display: If a joint mode is not specified, stage 2 cannot be set in the sequence.

Cause: If a joint mode is not specified, stage 2 cannot be set in the sequence.

Remedy: Either skip all of the sequence data specified in stage 2, or delete stage 2.

Code: 1101C702

Display: Sequence Data (D) does not exist.

Cause: There is not a placement sequence in Sequence Data (Type D).

Remedy: When operating the machine without a placement sequence, set the pass mode in

panel data to “1: Pass”.

Code: 1101C703

Display: “Position X” exceeds the range of the panel.

Cause: The sequence data”s X-coordinate is off the panel.

Remedy: Specify an X-coordinate which is within the panel size range.

Code: 1101C704

Display: “Position Y” exceeds the range of the panel.

Cause: The sequence data”s Y-coordinate is off the panel.

Remedy: Specify an Y-coordinate which is within the panel size range.

Code: 1101C705

Display: There are sequences on the same board with the same mark number.

Cause: A fiducial mark reading sequence exists which has duplicate mark numbers

within a single board.

Remedy: Revise either the “Board No.” or “Mark No.” in the sequence data.

Part 8 Chapter 1 Error Codes and Corrective Measures

Edition 2.0 8-1-1 XP-142E System Reference