XP-142E System Reference-SYS-XP142-2.0E.pdf.pdf - 第338页

1. Starting the Machine 1.1 The Proper Data Editor appears when starting the machine Symptoms: The Proper Data Editor is displayed automatically and no other messages appear. Note: The Proper Data Editor can be opened by…

3. Corrective Measures for Problems at the Machine

This section describes possible problems at the machine and measures to correct these

problems.

1. Starting the Machine

2. Screen Displays

3. The READY ON and START Buttons

4. The CYCLE STOP Button

5. Panel Loading and Unloading

6. MFU

7. Tape Cutter

1.1 The Proper Data Editor appears when starting the machine.

2.1 Display of the [Production Data] list is unusually slow.

2.2 Display of production program screens is unusually slow.

3.1 After pushing READY ON, the machine moves even though START has

not been pushed.

3.5 The READY ON button lights up but the START button does not flash.

4.1 During production, the machine does not stop when CYCLE STOP is pushed.

6.1 The machine cannot clamp or unclamp the MFU.

7.1 The tape cutter will not move.

3.2 The START button does not respond even though "Push the START switch"

appears on screen.

3.3 The servo power turns on when the machine is ready, even though the

READY ON button has not been pushed.

3.4 The servo power does not turn on when the machine is ready and READY

ON is pushed.

5.1 Production starts when before a panel arrives at the main station.

5.2 When loading a panel, the panel stops before arrival at the main station.

5.4 Error code 1503100E (Failed to convey panel) is displayed during panel

5.5 Error code 15032011 (Failed to convey panel) is displayed during panel

5.6 When finished producing a panel, the machine unloads the panel prematurely,

before the next machine issues a panel request signal.

5.7 When finished with production, the machine does not unload the panel to the

next machine.

5.8 Error code 15031010 (Failed to convey panel) is displayed during panel

unloading.

5.3 When loading a panel, the panel does not decelerate before arrival at the

main station.

8-3-2

8-3-3

8-3-4

8-3-5

8-3-6

Page

XP1S8001E

Part 8 Chapter 3 Corrective Measures for Problems at the Machine

Edition 2.0 8-3-1 XP-142E System Reference

1. Starting the Machine

1.1 The Proper Data Editor appears when starting the machine

Symptoms: The Proper Data Editor is displayed automatically and no other messages

appear.

Note: The Proper Data Editor can be opened by starting the machine with the

CYCLE STOP button pushed in.

Remedy: If a message appears before the Proper Data Editor opens, then follow the

instructions in the message. The CYCLE STOP button may be

malfunctioning. Contact a Fuji Machine dealer for assistance.

X007: CycleStopBtn: Cycle stop PB

2. Screen Displays

2.1 Display of the [Production Data] list is unusually slow.

Symptoms: Display of the [Production] - [Production Data] list is unusually slow, taking

up to several minutes to complete.

Note: As the size of the production data log file increases, the machine requires

increasingly more time to display the production data screen.

Remedy: Using the commands [Production] - [Production Data] - [Deletion Settings],

reduce the values of the [Days] or [Size] limitations.

Delete unnecessary files using the commands in [Production] - [Production

Data] - [Log File].

2.2 Display of production program screens is unusually slow.

Symptoms: Display of the production program screens that appear upon completion of

any of the following sequences is unusually slow, taking up to several

minutes to complete.

Note: As the number of command data files increases, the machine requires

increasingly more time to display production program screens.

[Production] - [Select Program]

[Program] - [Select Program]

[Program] - [Editor] - [Save] - [Browse]

[Program] - [Editor] - [Close] - [Browse] (Only after editing a program)

[Program] - [Editor] - [Mark] - [Mark File Load]

[Program] - [Editor] - [Part] - [Load Library]

[Program] - [Editor] - [Part] - [Part Type Edit] - [Load Library]

[Program] - [Editor] - [Part] - [Packaging Edit] - [Load Library]

[Program] - [File Manager]

Remedy: Delete unnecessary files at [Program] - [File Manager].

If files exist that are seldom used but still necessary, save them to a remote

location such as a floppy disk, then delete them from the machine.

Part 8 Chapter 3 Corrective Measures for Problems at the Machine

Edition 2.0 8-3-2 XP-142E System Reference

3. The READY ON and START Buttons

3.1 After pushing READY ON, the machine moves even though

START has not been pushed.

Symptoms: At the [Production] - [Automatic] screen, the READY ON button is pushed,

and the machine moves before the START button is pushed.

At the [Manual Operation] commands, the machine moves although the

START button has not been pushed.

Remedy: The following pushbutton switch may be malfunctioning. Contact a Fuji

Machine dealer for assistance.

X000: StartButton: Start PB

3.2 The START button does not respond even though “Push the

START switch” appears on screen.

Symptoms: When using the [Production] or [Manual Operation] screens, the START

button does not respond even though the message, “Push the START

switch,” appears on screen.

Remedy: The following pushbutton switch may be malfunctioning. Contact a Fuji

Machine dealer for assistance.

X000: StartButton: Start PB

3.3 The servo power turns on when the machine is ready, even

though the READY ON button has not been pushed.

Symptoms: When the start conditions are fulfilled (safety covers are closed, the

EMERGENCY STOP is released, etc.), the servo power turns on even though

the READY ON button has not been pushed.

The READY ON button is flashing when this happens.

Remedy: The following pushbutton switch may be malfunctioning. Contact a Fuji

Machine dealer for assistance.

X001: ReadyOnButton: READY ON PB

3.4 The servo power does not turn on when the machine is ready

and READY ON is pushed.

Symptoms: When the start conditions are fulfilled (safety covers are closed, the

EMERGENCY STOP is released, etc.) and the READY ON button is pushed,

the servo power does not turn on.

The READY ON button flashes normally.

Remedy: The following pushbutton switch may be malfunctioning. Contact a Fuji

Machine dealer for assistance.

X001: ReadyOnButton: READY ON PB

3.5 The READY ON button lights up but the START button does not

flash.

Symptoms: The start conditions are fulfilled and the READY ON button lights up when

pushed, but the START button does not flash.

Remedy: The following pushbutton switch may be malfunctioning. Contact a Fuji

Machine dealer for assistance.

X007: CycleStopBtn: Cycle stop PB

Part 8 Chapter 3 Corrective Measures for Problems at the Machine

Edition 2.0 8-3-3 XP-142E System Reference