XP-142E System Reference-SYS-XP142-2.0E.pdf.pdf - 第217页
Image Zoom-out To zoom-out, click the screen at the center of the desired zoom-out area. With each click, the zoom-out factor is halved until the original zoom factor is reached. If the zoom-out image extends beyond the …
Changing All Line Parameters
The parameters for all the currently active lines can be changed in a single operation at
the line parameter dialog box. If one of the selected lines has a "No Edge" setting, the
"Find Set" operation is executed for only the lines without this "No Edge" setting.
Deleting Lines
All the currently active seek lines are deleted when the [Active Delete] button is pressed.
Calipers
This is the calipers resetting mode. This mode can be established only when
the initial zoom-in factor is in effect.
When in this mode, the following functions are disabled: [Find All Cancel],
[Edge Position Correction], [Image Position Correction]
Active Delete
Deletes the currently active seek line.
Find Set Mode
This is the manual Find setting mode. This mode can be established only
when in the position seek line display mode. If switched to the inspection
line display mode while in this Find Set Mode, the Find Set Mode is ended,
and the line editor (input) mode is established. The [Active Delete] function
is disabled when in the Find Set Mode.
Find All Cancel
When seek lines which are not "Find Set" lines are clicked, a triangle mark
displays on those lines, and a Find setting is performed. If a seek line which
is already a "Find Set" line is selected, the Find status is canceled, and the
triangle mark clears from the screen.
* The display color for "No edge" seek lines is cyan, and a "Find Set" cannot
be performed on these lines even if they are clicked.
Zoom-out / Zoom-in
This is the image zoom-in and zoom-out mode. When in the zoom-in mode,
the [Active Delete] function is disabled.
Image Zoom-In
To zoom-in, click the screen at the center of the desired zoom-in area. With each click,
the zoom-in factor increases to x2, x4, x8, x16, x32 (max.). If the zoom-in image extends
beyond the boundaries of the original image, the zoom-in center is automatically
adjusted so that the boundaries are not violated.
Part 4 Chapter 2 Creating a Template From Existing Part Data
Edition 2.0 4-2-14 XP-142E System Reference
Image Zoom-out
To zoom-out, click the screen at the center of the desired zoom-out area. With each click,
the zoom-out factor is halved until the original zoom factor is reached. If the zoom-out
image extends beyond the boundaries of the original image, the zoom-out center is
automatically adjusted so that the boundaries are not violated.
Original Image Display
Restores the original image zoom factor when the display has been enlarged
(zoom-in).
Edge Position Correction
An edge position correction can be performed in the [Auto Find Set] ‡ [Edge
Position Correction] sequence.
An edge position correction can be performed on both inspection and
position seek lines regardless of the display mode.
Multiple measurement points display for lines where the edge was detected,
and the edge position correction was successful. (The number of multiple
measurement points is fixed at 5.)
Each of these operations are explained below.
Auto Find Set
If no Find seek lines have been set, the "Find Set" function is automatically executed.
Edge Position Correction
The line edge position is detected, and the seek line center is adjusted so that it is aligned
with the edge position.
The operation ends in failure if the line edge is not found, and an error message displays.
The failed line displays in a cyan color from the point immediately after the edge
position correction until the error message window is closed, and multiple measurement
points do not display.
When the edge position correction fails, the "Image position correction" "Template
generation completed" functions cannot be performed.
Image Position Correction
Performs vision processing, and the image center position and angle are
corrected using pair seek lines. This function is disabled if no pair lines are
set.
The screen's center position is corrected and re-displayed.
To correct the image, the editing image center and angle are corrected so that
the recognized workpiece is positioned at the center of the image. Moreover,
single seek lines are also corrected by the same amount as the image center
and angle. The coordinates and angles of pair seek lines remain unchanged,
and are not corrected. After all other corrections have been completed, an
edge position correction is performed.
Part 4 Chapter 2 Creating a Template From Existing Part Data
Edition 2.0 4-2-15 XP-142E System Reference
Center Line Display
When on, the editing image center lines (cross-hairs) display in red.
File Import
Loads a *.tpl file which can then be edited.
When the [File Import] button is pressed, a file selection window displays.
Select the desired file, then press [Open] to edit the template stored in that
file. Data which was being edited before the file was opened is abandoned.
Press [Cancel] to close the file selection window and return to the editing
screen.
Close
Ends the editing operation.
Line parameters examples are given below.
(A) For position lines (B) For inspection lines
[Type] Button
Sets the seek line type (Pair/Single).
Part 4 Chapter 2 Creating a Template From Existing Part Data
Edition 2.0 4-2-16 XP-142E System Reference