KE2010.Instruction Manual.Ver.2.01,Rev.08.pdf - 第1117页

34 E650354 Idle PW B Convey ing Error : PW B convey ing time out error of the center station on the Exit side. The process is forcibly terminated. Please remov e on the conveying route E650362 Idle PW B Convey ing Error …

E650275 Clamp error : Something is wrong with the backup motor movement of the center station.

The process is forcibly terminated. Please remove on the conveying route

E650276 Clamp error : Hole reference process at the center station finished illegally. The process is

forcibly terminated. Please remove on the conveying route

E650281 Clamp error : Backup plate of the center station on the Entrance side went up illegally. The

process is forcibly terminated. Please remove on the conveying route

E650282 Clamp error : Time-out occurred while backup plate of the center station on the Entrance

side went up. The process is forcibly terminated. Please remove on the conveying route

E650283 Clamp error : Time-out occurred while backup plate of the center station on the Entrance

side went down illegally. The process is forcibly terminated. Please remove on the

conveying route

E650284 Clamp error : Time-out occurred while backup plate of the center station on the Entrance

side went down. The process is forcibly terminated. Please remove on the conveying route

E650285 Clamp error : Something is wrong with the backup motor movement of the center station on

the Entrance side. The process is forcibly terminated. Please remove on the conveying

route

E650286 Clamp error : Hole reference process at the center station on the Entrance side finished

illegally. The process is forcibly terminated. Please remove on the conveying route

E650291 Clamp error : Backup plate of the center station on the Exit side went up illegally. The

process is forcibly terminated. Please remove on the conveying route

E650292 Clamp error : Time-out occurred while backup plate of the center station on the Exit side

went up. The process is forcibly terminated. Please remove on the conveying route

E650293 Clam error : Backup plate of the center station on the Exit side went down illegally. The

process is forcibly terminated. Please remove on the conveying route

E650294 Clamp error : Time-out occurred while backup plate on the center station on the Exit side

went down. The process is forcibly terminated. Please remove on the conveying route

E650295 Clamp error : Something is wrong with the backup motor movement on the center station on

the Exit side. The process is forcibly terminated. Please remove on the conveying route

E650296 Clamp error : Hole reference process at the center station on the Exit side finished illegally.

The process is forcibly terminated. Please remove on the conveying route

W650309 Idle PWB Conveying Error : PWB is detected on the conveying route. Please remove it

W650311 Idle PWB Conveying Error : A PWB is detected on the center station. Please remove it

W650312 Idle PWB Conveying Error : A PWB is detected on the center station on the Entrance side.

Please remove it

W650313 Idle PWB Conveying Error : A PWB is detected on the center station on the Exit side.

Please remove it

W650314 Idle PWB Conveying Error : A PWB is detected on the OUT buffer. Please remove it

W650319 Idle PWB Conveying Error : In operation of Idle PWB conveying

E650321 Idle PWB Conveying Error : Illegal input buffer motor movement. The process is forcibly

terminated. Please remove on the conveying route

E650322 Idle PWB Conveying Error : PWB conveying error of Input buffer. The process is forcibly

terminated. Please remove on the conveying route

E650323 Idle PWB Conveying Error : PWB conveying error of Input buffer. The process is forcibly

terminated. Please remove on the conveying route”

E650324 Idle PWB Conveying Error : PWB conveying time out error of Input buffer. Please remove

on the conveying route

E650334 Idle PWB Conveying Error : PWB conveying time out error of the center station. The

process is forcibly terminated. Please remove on the conveying route

E650342 Idle PWB Conveying Error : PWB conveying error of the center station on the Entrance side.

The process is forcibly terminated. Please remove on the conveying route

E650343 Idle PWB Conveying Error : PWB conveying error of the center station on the Entrance side.

The process is forcibly terminated. Please remove on the conveying route

E650344 Idle PWB Conveying Error : PWB conveying time out error of the center station on the

Entrance side. The process is forcibly terminated. Please remove on the conveying route

E650352 Idle PWB Conveying error : PWB conveying error of the center station on the Exit side. The

process is forcibly terminated. Please remove on the conveying route

E650353 Idle PWB Conveying Error : PWB conveying error of the center station on the Exit side. The

process is forcibly terminated. Please remove on the conveying route

E650354 Idle PWB Conveying Error : PWB conveying time out error of the center station on the Exit

side. The process is forcibly terminated. Please remove on the conveying route

E650362 Idle PWB Conveying Error : PWB conveying error of Output buffer. The process is forcibly

terminated. Please remove on the conveying route

E650364 Idle PWB Conveying Error : PWB conveying time out error of Output buffer.

E650365 Idle PWB Conveying Error : PWB conveying time out error of Output buffer. The process is

forcibly terminated. Please remove on the conveying route

E651001 Returning to ORIGIN has not been done

E651002 An error occurred when returning to ORIGIN

E651003 There is no need to move

E651004 The traveling movement has discontinued due to Backup pin detection

E651005 More than one command were tried to start at one time

E651006 An error occurred while issuing command run event

E651007 A time-out occurred while waiting for a command to be complete

E651008 Although the motor stopped, encoder does not stop

E651009 An error occurred when starting the motor

E651010 An error occurred while waiting for the motor to stop

E651011 An error occurred while reading ORIGIN sensor in

Error Messages on CVS

Error code Message

E690001 CVS is not installed

E690002 Impossible to switch to Resistance Measurement mode since the probe has not shut down.

Please shut the probe down then try again

E690003 Impossible to switch to Condenser Measurement mode since the probe has not shut down.

Please shut the probe down then try again

E690004 The measurement mode is not correct

E690005 Parameter to control probe is not correct

E690006 Probe has to be shut down to measure resistance. Please shut probe then try again

E690007 Probe has to be shut down to measure condenser. Please shut probe then try again

E690008 Diode measurement is not available unless probe shuts down. | Please shut probe then try

again

E690009 The measurement is impossible since measurement mode is not set to Resistance

measurement. Please switch to the Resistance measurement mode then try again

E690010 The measurement is impossible since measurement mode is not set to Condenser

measurement.

Please switch to the Condenser measurement mode then try again

E690011 The measurement is impossible since measurement mode is not set to Diode

measurement. Please switch to the Diode measurement mode then try again

E690012 The measurement is impossible since the gotten measurement mode is set to Resistance

measurement

E690013 The measurement is impossible since the gotten measurement mode is set to Condenser

measurement

E690014 The measurement is impossible since the gotten measurement mode is set to Diode

measurement

E690015 The resistance when zero-adjusting is abnormal. Please check if probe short-circuits or not

E690016 A time-out occurred while reading resistance in

E690017 A time-out occurred while reading volume in

E690018 A time-out occurred while reading voltage in

E690019 The measured resistance does not get stable. Please check the probe status

E690020 The measured volume does not get stable. Please check the probe status

E690021 The measured voltage does not get stable.

Please check the probe status”

E690022 Something is wrong with the measured resistance

E690023 Something is wrong with the measured volume

E690024 Something is wrong with the measured voltage”

E690025 Something is wrong with the measured resistance(unit)

E690026 Something is wrong with the measured volume(unit)

E690027 Something is wrong with the measured voltage(unit)”

E690028 Resistance can no be measured. Please check if probe shuts down properly

E690029 Volume can not be measured. Please check if probe shuts down properly

E690030 Voltage can not be measured. Please check if probe shuts down properly