KE2010.Instruction Manual.Ver.2.01,Rev.08.pdf - 第1118页

35 Error M essages on CVS Error code Message E690001 CVS is not installed E690002 Impossible to switch to Resistance M easurement mode since the probe has not shut down. Please shut the probe down then try again E690003 …

E650354 Idle PWB Conveying Error : PWB conveying time out error of the center station on the Exit

side. The process is forcibly terminated. Please remove on the conveying route

E650362 Idle PWB Conveying Error : PWB conveying error of Output buffer. The process is forcibly

terminated. Please remove on the conveying route

E650364 Idle PWB Conveying Error : PWB conveying time out error of Output buffer.

E650365 Idle PWB Conveying Error : PWB conveying time out error of Output buffer. The process is

forcibly terminated. Please remove on the conveying route

E651001 Returning to ORIGIN has not been done

E651002 An error occurred when returning to ORIGIN

E651003 There is no need to move

E651004 The traveling movement has discontinued due to Backup pin detection

E651005 More than one command were tried to start at one time

E651006 An error occurred while issuing command run event

E651007 A time-out occurred while waiting for a command to be complete

E651008 Although the motor stopped, encoder does not stop

E651009 An error occurred when starting the motor

E651010 An error occurred while waiting for the motor to stop

E651011 An error occurred while reading ORIGIN sensor in

Error Messages on CVS

Error code Message

E690001 CVS is not installed

E690002 Impossible to switch to Resistance Measurement mode since the probe has not shut down.

Please shut the probe down then try again

E690003 Impossible to switch to Condenser Measurement mode since the probe has not shut down.

Please shut the probe down then try again

E690004 The measurement mode is not correct

E690005 Parameter to control probe is not correct

E690006 Probe has to be shut down to measure resistance. Please shut probe then try again

E690007 Probe has to be shut down to measure condenser. Please shut probe then try again

E690008 Diode measurement is not available unless probe shuts down. | Please shut probe then try

again

E690009 The measurement is impossible since measurement mode is not set to Resistance

measurement. Please switch to the Resistance measurement mode then try again

E690010 The measurement is impossible since measurement mode is not set to Condenser

measurement.

Please switch to the Condenser measurement mode then try again

E690011 The measurement is impossible since measurement mode is not set to Diode

measurement. Please switch to the Diode measurement mode then try again

E690012 The measurement is impossible since the gotten measurement mode is set to Resistance

measurement

E690013 The measurement is impossible since the gotten measurement mode is set to Condenser

measurement

E690014 The measurement is impossible since the gotten measurement mode is set to Diode

measurement

E690015 The resistance when zero-adjusting is abnormal. Please check if probe short-circuits or not

E690016 A time-out occurred while reading resistance in

E690017 A time-out occurred while reading volume in

E690018 A time-out occurred while reading voltage in

E690019 The measured resistance does not get stable. Please check the probe status

E690020 The measured volume does not get stable. Please check the probe status

E690021 The measured voltage does not get stable.

Please check the probe status”

E690022 Something is wrong with the measured resistance

E690023 Something is wrong with the measured volume

E690024 Something is wrong with the measured voltage”

E690025 Something is wrong with the measured resistance(unit)

E690026 Something is wrong with the measured volume(unit)

E690027 Something is wrong with the measured voltage(unit)”

E690028 Resistance can no be measured. Please check if probe shuts down properly

E690029 Volume can not be measured. Please check if probe shuts down properly

E690030 Voltage can not be measured. Please check if probe shuts down properly

Error Messages on Safety

Error code Message

E691001 Input/Output buffer status of CCL-48M does not get ready

E691002 Writing-in buffer of flush memory does not get useable

E691003 Deleting cue of flush memory does not get useable

E691004 WSM(Write State Machine) of flush memory does not get ready

E691005 Write-in voltage range error occurred in flush memory control

E691006 Write-in error occurred in flush memory control

E691007 Write-in error occurred in flush memory control

E691008 Command sequence error occurred in flush memory control

E691009 Lock Bit Set error occurred n flush memory control

E691010 Lock Bit Clear error occurred in flush memory control

E691011 The check word for the common data of flush memory is abnormal

E691012 The checksum for the common data of flush memory is abnormal

E691013 The data version for the common data of flush memory is abnormal

E691014 The data length for the common data of flush memory is abnormal

E691015 The data kind for the common data is abnormal