KE2010.Instruction Manual.Ver.2.01,Rev.08.pdf - 第989页
184 E610233 “RZ2 Driver alarm occurred” [Cause] An abnor m al m atter happened to the Z axis servo driver on the right head2. [Treatm ent] Pleas e turn of f the power supply of your machine. If the error oc curs even af …
183
④ The set value for the air pressure detecting sensor is too low. Please reset the
value of the sensor that is installed next to the air combination to 0.45Mpa.
⑤ The air pressure detecting sensor is broken. Please examine if a connecting
cable connects to the connector properly. If the cable connects to the
connector properly, the sensor itself is broken.
E610227 “The error not forecast occurred”
[Cause] An undefined error occurred.
[Treatment] Please turn off the power supply of your machine and reboot it.
E610228 “LZ1 Driver alarm occurred”
[Cause] An abnormal matter happened to the Z axis servo driver on the right head1.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Z axis
servo driver on the left head1 with a new one.
E610229 “LZ2 Driver alarm occurred”
[Cause] An abnormal matter happened to the Z axis servo driver on the right head2.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Z axis
servo driver on the left head2 with a new one.
E610230 “LZ3 Driver alarm occurred”
[Cause] An abnormal matter happened to the Z axis servo driver on the right head3.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Z axis
servo driver on the left head3 with a new one.
E610231 “LZ4 Driver alarm occurred”
[Cause] An abnormal matter happened to the Z axis servo driver on the right head4.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Z axis
servo driver on the left head4 with a new one.
E610232 “RZ1 Driver alarm occurred”
[Cause] An abnormal matter happened to the Z axis servo driver on the right head1.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Z axis
servo driver on the right head1 with a new one.
184
E610233 “RZ2 Driver alarm occurred”
[Cause] An abnormal matter happened to the Z axis servo driver on the right head2.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Z axis
servo driver on the right head2 with a new one.
E610234 “RZ3 Driver alarm occurred”
[Cause] An abnormal matter happened to the Z axis servo driver on the right head3.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Z axis
servo driver on the right head3 with a new one.
E610235 “RZ4 Driver alarm occurred”
[Cause] An abnormal matter happened to the Z axis servo driver on the right head4.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Z axis
servo driver on the right head4 with a new one.
E610236 “LT1 Driver alarm occurred”
[Cause] An abnormal matter happened to the Theta axis servo driver on the left head1.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Theta axis
servo driver on the left head1 with a new one.
E610237 “LT2 Driver alarm occurred”
[Cause] An abnormal matter happened to the Theta axis servo driver on the left head2.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Theta axis
servo driver on the left head2 with a new one.
E610238 “LT3 Driver alarm occurred”
[Cause] An abnormal matter happened to the Theta axis servo driver on the left head3.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Theta axis
servo driver on the left head3 with a new one.
E610239 “LT4 Driver alarm occurred”
[Cause] An abnormal matter happened to the Theta axis servo driver on the left head4.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Theta axis
servo driver on the left head4 with a new one.
E610240 “RT1 Driver alarm occurred”
[Cause] An abnormal matter happened to the Theta axis servo driver on the right head1.
185
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Theta axis
servo driver on the right head1 with a new one.
E610241 “RT2 Driver alarm occurred”
[Cause] An abnormal matter happened to the Theta axis servo driver on the right head2.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Theta axis
servo driver on the right head2 with a new one.
E610242 “RT3 Driver alarm occurred”
[Cause] An abnormal matter happened to the Theta axis servo driver on the right head3.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Theta axis
servo driver on the right head3 with a new one.
E610243 “RT4 Driver alarm occurred”
[Cause] An abnormal matter happened to the Theta axis servo driver on the right head4.
[Treatment] Please turn off the power supply of your machine. If the error occurs even after
the reboot, please see if the cables are connected properly. If the error still occurs
even when the cables are connected properly, you need to replace the Theta axis
servo driver on the right head4 with a new one.
E610300 “An error occurred when ComRes command send”
[Cause] Command sending of Command-response type failed. This is an error that
occurred during the data communication in the machine.
[Treatment] • Please turn off the power supply of your machine and reboot it.
• If the error occurred after the installation or the versionup of the software, you
need to re-install the software.
• If the treatments above do not work, there is a possibility that board(s) in the
machine is broken. You need to replace it(them) with new ones.
E610301 “An error occurred when ComRes response receive”
[Cause] Response reception of Command-Response type failed. This is an error that
occurred during the data communication in the machine.
[Treatment] • Please turn off the power supply of your machine and reboot it.
• If the error occurred after the installation or the versionup of the software, you
need to re-install the software.
• If the treatments above do not work, there is a possibility that board(s) in the
machine is broken. You need to replace it(them) with new ones.