KE2010.Instruction Manual.Ver.2.01,Rev.08.pdf - 第1256页

173 E610044 “Head tr aveling coordinates are w i thin the head i nterference range(STOP)” [Cause] T he lef t and right heads can not m ove at high s peed since they interfere each other when they travel to the spec ified…

172

E610042 “A shadow is detected while nozzle detection after returning

nozzles”

[Cause] A nozzle was detected at a position where normal nozzles are not supposed to be

detected in the installation status checking which is performed after the nozzle

returning. There is a possibility that the nozzle could not be returned right or the

window of the laser sensor is dirty.

[Treatment] 1. If the nozzle was returned properly

There is a possibility that the window of the laser sensor is dirty. Please clean

the window of the sensor. You can check the dirt of the window with the

following procedures. Select [Manual Control] from the menu bar, and then

select [Control(C)] [Head(H)] [Laser Control(L)]. Select a concerned laser

sensor in ‘Control’ unit, and then select ‘Image displaying’ from ‘Control Item’

frame. By enabling ON, an image data will be shown.

2. If the nozzle was not returned properly.

Please take the nozzle off the head part and set it on ATC. The following

causes are possible for why the nozzle could not be returned correctly.

①

There is an abnormal nozzle. Please examine if there is any obstructions

on the installation part on the head, or if it is damaged or deformed

②

Something is wrong with the movement of the ATC slide plate. In this

case, the following cases can be possible.

A) The speed controller of the slide plate driving cylinder is wrung to its

minimum limit. Please loosen the speed controller of the slide plate

driving cylinder.

B) The installation position of the slide plate ON/OFF sensor is wrong.

There is a possibility that the sensor gets ON before the slide plate

fully opens/closes. Please re-adjust the sensor to where it gets

ON/OFF properly.

C) There is an obstruction that prevents the slide plate from being

opened/closed. Please examine if there is anything caught in near

the slide plate.

D) The air supplying to the slice plate driving cylinder is not correct.

Please examine if the air pipe is properly connected.

E) The nut on the shaft of the slide plate driving cylinder is loose and the

connector part of the slide plate plays too much. Please examine if

the nut is tightened up enough.

③

The ATC coordinates or the nozzle change height is not correct. If you

change the coordinates or the height, please select [Setup(S)] [MS

parameter] and follow the Maintenance manual. For MS parameter, it is

limited that who can change the parameter by the user level setting.

E610043 “Head traveling coordinates are within the head interference

range(SLOW)”

[Cause] The left and right heads can not move at high speed since they interfere each

other when they travel to the specified ATC position simultaneously. Some

program versions in the machine may be clashing with each other.

[Treatment] • Please turn off the power supply of your machine and reboot it.

• If the error occurred after the installation or the versionup of the software, you

need to re-install the software.

• If the treatments above do not work, there is a possibility that MPX board(s) in

the machine is broken. You need to replace it(them) with new ones.

173

E610044 “Head traveling coordinates are within the head interference

range(STOP)”

[Cause] The left and right heads can not move at high speed since they interfere each

other when they travel to the specified ATC position simultaneously. Some

program versions in the machine may be clashing with each other.

[Treatment] • Please turn off the power supply of your machine and reboot it.

• If the error occurred after the installation or the versionup of the software, you

need to re-install the software.

• If the treatments above do not work, there is a possibility that MPX board(s) in

the machine is broken. You need to replace it(them) with new ones.

E610045 “ATC(L) slide plate can not be shut down”

[Cause] ATC slide plate has to be closed when trying to change nozzles but it was open.

The process of closing the slide plate yet the plate did not get closed. This error is

likely to happen when the lock valve of the solenoid valve, which drives the slide

plate remains closed. The following causes are also possible.

①

The air is not being supplied properly.

②

The slide plate that slides left and right to open and close the plate in the ATC

unit does not work properly.

③

The sensor which detects the position of the slide plate is not tuned well or

broken.

[Treatment] Please select [Manual Control] from the menu bar, and then select [Control(C )]

[Other(O)] [ATC Control(A)]. Set ‘Control Unit’ to ‘light ATC’, and select ‘Slide

plate Control(A)’ from the ‘Control Item’ frame’ to open/close the slide plate.

Please perform one of the treatments below according to the result you get.

1. Slide plate works properly.

1.1 The ‘Slide plate OFF sensor’ in the ‘Status’ displaying frame gets ON/OFF.

The speed controller of the Slide plate driving cylinder might be wrung too

much toward its minimum limit. Please loosen the controller.

1.2 The ‘Slide plate OFF sensor’ in the ‘Status’ displaying frame does not get

ON/OFF.

①

There is a possibility that the Slide plate OFF sensor was adjusted to

out of the Cylinder’s movable range. Please re-adjust the sensor to

where it gets ON/OFF.

②

If the treatment1 does not work, there is a possibility that the slide

plate OFF sensor is broken. It could be that the wiring came off the

connector part, that a contact pin in the connector part is broken, that

the wiring got cut off, or that the sensor itself is broken. Please

examine the wiring and connector. If any of them are broken, you

need to replace them with new ones.

③

If the treatment2 does not work, a PCB is broken or the wiring

between the PCBs is bad.

2. Slide plate does not work.

①

There is a possibility that the lock valve of the solenoid valve, that drives

the slide plate, is closed. Please make sure that the lock valve of the

solenoid valve is opened all the way.

②

There is a possibility that a nozzle is not installed in the ATC correctly and

that prevent the slide plate from sliding properly. Please see if nozzles are

correctly installed in the ATC.

③

There is a possibility that a component or implement got caught in the

sliding part of the slide plate and that prevents the slide plate from sliding

properly. Please see if there is anything on the slide plate.

④

There is a possibility that the air supplying pipes to the slide plate driving

cylinder have a problem. It could be that the speed controller is fully

174

tightened up, that the air pipe came off the cylinder, or a wrong air pipe is

connected to the cylinder. Please see the air pipes and make sure that

correct pipes are connected.

⑤

There is a possibility that the connecting part between the shaft of the

slide plate driving cylinder and the slide plate has a problem. It could be

that the nut attached to the tip of the shaft fell off, that the shaft got

chipped or broken, or that the plate got chipped or broken. You need to

have the damaged part repaired or replace it with a new one.

⑥

There is a possibility that the slide plate driving cylinder is broken. Please

stop the air supplying on the machine and see if the slide plate works fine

manually. If the plate does not work smoothly, you need to replace it with

a new one.

⑦

There is a possibility that the slide plate driving solenoid valve is broken. It

could be that the wiring came off the connector part, that a contact pin in

the connector part is broken, that the wiring got cut off, or the solenoid

valve itself is broken. Please examine the wiring and connectors. If any of

them are broken, you need to replace them with new ones..

⑧

If the treatments mentioned above do not work, a PCB is broken or the

wiring between the PCBs is bad.

E610046 “ATC(R) slide plate can not be shut down”