KE2010.Instruction Manual.Ver.2.01,Rev.08.pdf - 第815页
10 Q302004 Error has occurred during nozz le installation. Move to parking position? Q302005 Ex tend shuttle? Q302006 Do you interrupt automatic measurement? Q302007 A nozz le is fixed to %s. D o you want to auto-return …
9
Error Messages on the Machine Setup Operations
Error code Message
E301000 Memory allocation error
E301001 There is no input character
E301002 Input character has irregularities
E301003 Input value exceeds predetermined data range. (Data range:%s)
E301012 An error occurred while measuring nozzle height by Laser
E301015 Specify user’s individual nozzle No.
E301016 An error occurred while taking nozzles off
E301017 Selected device can not move to this position. Please reselect other device on HOD
E301018 Selected device is not installed. Please reselect other device on HOD
E301019 Return to home has not yet been completed
E301020 MTC power off
E301021 MTC offline
E301023 There is no installed head
E301024 Selected device is disable. Please reselect other device on HOD
E301025 MTC is disable
E301026 Servo is in the free state
W301027 Teached data is invaled
E301028 Length of the nozzle is too short. Please check the nozzle
E301032 MTC is in the supply state
E301035 MTS is disable
E301036 MTS power off
E301037 MTS offline
E301038 MTS cannot move because of cover opening
E301039 The door of MTS opens
E301040 There is no specified stacker with the tray steps number
E301042 Because MTS is selected, the IC conveyor belt is not assembled to a rear side
E301044 Nozzle length is too long. Please check out the nozzle
E301046 Only nozzle No. has been input. Please specify nozzle types
E301047 An error occurred while taking nozzles off. The process is discontinued
E301048 Vacuum Calibration unit position can not be measured
E301049 An error occurred while installing nozzles. [Error occurs] %d [Error No.] %d [Error info] %d
E301050 In 2030, Vacuum Calibration can be set for only R1 through R4
E301051 Vacuum Calibration can be et only for small-diameter nozzles. (Settable range : 1 - %d)
E301052 Any heads have not been specified
E301053 The Changer table can not be installed on the rear side since MTC/MTS have been selected
E301054 MTC/MTS can not be connected to 2000 series machines at the same time
E301055 An error on axes occurred
E301056 An error on XY axes occurred
E301057 An error on Z axis occurred
E301058 Specified 508 nozzle has not been assigned yet. Please execute nozzle assignment
E301059 It was impossible to learn the height. Please checck out the vacuum value
E301060 DTS/MTS can not be connected to 2000 series machines at the same time
E301061 Feeder float detector can not be set only out position
Q302000 Reset I/O?
Q302001 Exit machine setup. Set value is saved?
Q302002 Error has occurred during automatic measurement of nozzle. Do you interrupt automatic
measurement?
Q302003 Return to home has not yet been completed. Return to home?
10
Q302004 Error has occurred during nozzle installation. Move to parking position?
Q302005 Extend shuttle?
Q302006 Do you interrupt automatic measurement?
Q302007 A nozzle is fixed to %s. Do you want to auto-return the nozzle?
Q302008 Extend MTS mark?
Q302009 Vacuum Calibration has been set already. (ATC No:%s) Would you like to disable the
setting?
Q302010 An error occurred during Auto. measuring nozzles. Would you like to discontinue the Auto.
measuring on the left station?
Q302011 An error occurred while installing nozzles. Would you like to move to the parking position?
[Error occurs] ? [Error No.] ? ?[ Error Info.] ???
Q302012 Move Z axis to where nozzles are taken off. Is that OK?
Q302013 Return Z axis to Laser height position. Is that OK?
Q302014 Please check if the backup plate is lifted up enough. It may be a little hard to see pins
when the plate is not lifted up. | Would you like to continue?
Q302015 There may be some units with ON state. Would you like to initialize these units?
I303000 Return to home of %s
I303001 Nozzle is removed from %s to ATC
I304000 Set online for MTC
I304001 Remove the nozzle from %s
I304002 A nozzle of %s is removed and return to %s of ATC
I304003 Set online for MTS
I304004 Please close the door of MTS
11
Error Messages on Manual Control Operations
Error code Message
E316001 Memory allocation error
E316002 Shared memory open error
E316011 There is no input character
E316012 Input character has irregularities
E316013 Input value exceeds predetermined data range
E316021 Return to home has not yet been completed
E316022 Servo is in the free state
E316031 Selected device is not install. Please reselect other device on HOD
W316041 There is no ATC that is allocated with nozzle. Allocate nozzle to ATC when setting up the
machine
W316042 Nozzle is not set on head
E316051 Z axis limit has been exceeded
E316101 Error has occurred when setting laser parameters code:%ld
E316102 Error has occurred during laser measurement(ONCE) code:%ld
E316103 Error has occurred during laser measurement(SWEEP) code:%ld
E316104 Error has occurred during the nozzle presence check | code:%ld
E316105 Error has occurred during the image data obtain. code:%ld
E316106 Error has occurred during the edge check data learning. code:%ld
E316107 Data has not been learned
E316301 MTC power off
E316302 MTC offline
E316303 MTC is in the supply state
E316401 MTS power off
E316402 MTS offline
E316403 MTS cannot move because of cover opening
E316404 The door of MTS opens
E316405 There is no specified stacker with the tray steps number
E316501 Error has occurred on axis code:%ld
E316502 The initialization error of transportation occurred. Return to home is interrupted. Error
code:%ld
E316503 The PWB was detected in the transportation road
Q317001 Exit manual control. Reset I/O?
Q317011 Return to home has not yet been completed. Return to home?
Q317021 Cannot return component. Trash component?
Q317031 Do you interrupt process?
Q317041 Is the tray of MTS stored?
I318001 Remove the component from %s
I318011 Set online for MTC
I318021 Set online for MTS
I318022 Please close the door of MTS
I318023 Remove the PWB on Conveyor