KE2010.Instruction Manual.Ver.2.01,Rev.08.pdf - 第877页

72 E316051 “Z axis l imit has been exceeded” [ Ｃ ause] Z ax is coor dinate exceeded its lim it. The ax is can not m ove any further. [Treatm ent] Please m ove the axis within the lim itation. E316101 “Error has occurred …

100%1 / 1361
71
E316001 “Memory allocation error”
[Cause] The working space can not be saved.
[Treatment] Please add some more memory available to save the working space.
E316002 “Shared memory open error”
[Cause] The shared memory could not be open.
[Treatment] Please shut down the your machine and re-start it.
E316011 “There is no input character”
[Cause] There was no character when you hit Enter key to define characters.
[Treatment] Please enter characters.
E316012 “Input character has irregularities”
[Cause] The letter strings had irregularities when defining the input.
[Treatment] Please enter proper characters.
E316013 “Input value exceeds predetermined data range”
[Cause] The value when defining the input exceeded the input range.
[Treatment] Please enter the values that are within the range.
E316021 “Return to home has not yet been completed”
[Cause] The axis has not yet been returned to home.
[Treatment] Please perform the Return to home with ORIGIN switch.
E316022 “Servo is in the free state”
[Cause] The axis could not move since the servo is not locked.
[Treatment] Please lock the servo with S-FREE switch.
E316031 “Selected device is not install. Please reselect other device on HOD”
[Cause] You could not go into the teaching mode since the device selected by HOD has
not been installed.
[Treatment] Please reselect the device which is currently installed.
W316041 “There is no ATC that is allocated with nozzle. Allocate nozzle to
ATC when setting up the machine”
[Cause] Although Nozzle change was chosen in ATC control, no nozzle has been
assigned to the ATC.
[Treatment] Please allocate nozzles to ATC in ATC Nozzle allocation in Machine Setup.
W316042 “Nozzle is not set on head”
[Cause] Although Nozzle returning was chosen in ATC control, no nozzle has been
installed on the specified head.
[Treatment] Please install a nozzle on the head, then try again.
72
E316051 “Z axis limit has been exceeded”
[Ｃause] Z axis coordinate exceeded its limit. The axis can not move any further.
[Treatment] Please move the axis within the limitation.
E316101 “Error has occurred when setting laser parameters code:%ld”
[Cause] An abnormal matter happened when setting the Laser parameter.
?: Error code.
-1: A communication error occurred.
[Treatment] Please reference [Status list] in [Laser Control] in Manual Control.
E316102 “Error has occurred during laser measurement(ONCE) code:%ld”
[Cause] An error occurred during the measurement(ONCE) by laser.
?: Error code.
-1 : A communication error.
Other : Please reference [Status list] in [Laser Control] in Manual Control.
[Treatment] Please reference [Status list] in [Laser Control] in Manual Control.
E316103 “Error has occurred during laser measurement(SWEEP) code:%ld”
[Cause] An error occurred during the measurement(SWEEP) by laser.
?: Error code
-1: A communication error occurred.
-2: An axis error occurred
Other: Please reference [Status list] in [Laser Control] in Manual Control.
[Treatment] Please reference [Status list] in [Laser Control] in Manual Control.
E316104 “Error has occurred during the nozzle presence check code:%ld"
[Cause] An error occurred during the measurement(ONCE) by laser.
?: Error code.
-1 : A communication error.
[Treatment] Please reference [Status list] in [Laser Control] in Manual Control.
E316105 “Error has occurred during the image data obtain. code:%ld"
[Cause] An error occurred while getting the Image data by laser.
?: Error code
-1: A communication error occurred.
Other: Please reference [Status list] in [Laser Control] in Manual Control.
[Treatment] Please reference [Status list] in [Laser Control] in Manual Control.
E316106 “Error has occurred during the edge check data learning.
code:%ld"
[Cause] An error occurred while getting the Edge check by laser.
?: Error code.
-1: A communication error occurred.
Other: Please reference [Status list] in [Laser Control] in Manual Control
[Treatment] Please reference [Status list] in [Laser Control] in Manual Control.
E316107 “Data has not been learned”
[Cause] Z axis coordinate by HMS could not be learned since it was out of the
73
measurement range (-40mm through +40mm)
[Treatment] Please check and see if the measuring position (XY coordinates) of HMS is
correct or not.
E316301 “MTC power off”
[Cause] The power supply of MTC is off.
[Treatment] Please turn on the power supply of MTC, and make it online.
E316302 “MTC offline”
[Cause] MTC is not online
[Treatment] Please make MTS online.
E316303 “MTC is in the supply state”
[Cause] MTC can not be controlled since it is in the Supply (component change) state.
[Treatment] Please make MTC a normal status.
E316401 “MTS power off”
[Cause] Failed to draw the MTS tray out since the MTS was not ON.
[Treatment] Please turn on the power supply of MTS.
E316402 “MTS offline”
[Cause] Failed to draw the MTS tray out since the MTS was not online.
[Treatment] Please make MTS online.
E316403 “MTS cannot move because of cover opening”
[Cause] Failed to draw the MTS tray out since the cover of the machine was open.
[Treatment] Please close the cover.
E316404 “The door of MTS opens”
[Cause] Failed to draw the MTS tray out since the MTS door was open.
[Treatment] Please close the MTS door.
E316405 “There is no specified stacker with the tray steps number”
[Cause] Failed to draw the MTS tray out since there was no stacker which has the
specified number of trays.
[Treatment] Please set the stacker with specified number of trays.
E316501 “Error has occurred on axis code:%ld”
[Cause] An error occurred while an axis was traveling.
[Treatment]
E316502 “The initialization error of transportation occurred. Return to home
is interrupted. Error code:%ld”
[Cause] The initialization error of transportation occurred..