Omron V-TS Teaching Manual.pdf.pdf - 第6页
5 Precautions for Correct Use Observe the following precautions to prevent failure to operate, malfunctions, or undesirable effect s on product performance. (1) S tore the m ain syst em in a loc ation which meet s the fo…
4
applications except SMT, Omron shall not provide any warranty for such Omron
products, unless otherwise specifically agreed or unless the applications are
intended by Omron.
(6) When using inspection program and library by more than one AOI machine, the
result is sometimes different between each AOI machine. Before using AOI
machine, please confirm inspection results between more than one AOI
machines are equal each other. If necessary, please tune the parameters of each
inspection program and other conditions.
4. Warranty Terms and Conditions
The terms and conditions for warranty of Omron products are as follows:
(1) Warranty period: Omron warrants that products shall be free of material defects
and or workmanship for a period of one year after the date of purchase or the
date when installed at the specified location.
(Excepting in the case where there is additional description in Catalogues)
(2) Coverage: Omron, at its own discretion, will provide one of the following two
services for malfunctioning Omron products:
(a) Free repair of the malfunctioning Omron products at an Omron maintenance
service location.
(No repair support is available for electronic components)
(b) Free replacement of the malfunctioning Omron products with the same
number of replacement/alternative products.
(3) Exceptions: Omron will not cover Omron products (including the data such as
inspection programs are corrupted.) under its warranty if the cause of the
malfunction falls under any of the following.
(a) Usage in a manner other than the original intended use for the Omron
products.
(b) Usage outside of the usage conditions.
(c) Usage of the product against the conditions described in "3. NOTE ABOUT
USE"
(d) Modification or repair made to the Omron product by other than Omron
personnel.
(e) Software program embedded by other than Omron or usage of such software.
(f) Cause which could not have been foreseen with the level of science and
technology at the time of shipping from Omron.
(g) Causes originating from other than Omron or Omron products (including
causes such as, but not limited to, natural disasters).
5. Limitation of Liability
The warranty set out in these Terms and Conditions is the whole and sole liability for
Omron products.
There are no other warranties, expressed or implied. Omron and the distributors of
Omron products are not liable for any damages which may arise from or be related to
Omron products.
6. Export Controls
Customers of Omron products shall comply with all applicable laws and regulations
of Japan and/or other relevant countries with regard to security export control, when
exporting Omron products and/or technical documents or providing such products
and/or documents to a non-resident. Omron may not provide customers with
Omron products and/or technical documents should they fail to comply with such
laws and regulations.
5
Precautions for Correct Use
Observe the following precautions to prevent failure to operate, malfunctions, or undesirable effects
on product performance.
(1) Store the main system in a location which meets the following conditions:
Temperature of 10 to 40 °C
Humidity of 35 to 80%
No direct sunlight
No possibility of dew condensation
No water leakage or water
(2) Provide enough space in the front and back of the system for operation and maintenance.
Please don't install the VT-S720 in such a way that the fan area is blocked or cover it.
(3) OMRON will move the system at delivery or relocation. When moving the system after
initial installation, be sure to contact OMRON sales office.
(4) Inspect circuit boards of the sizes within the specification.
(5) Do not touch the cables and connectors.
(6) Do not give the system a shock, or the system would be broken down.
(7) Do not touch the camera and lens as an adjustment has been performed before shipment.
Doing so may affect inspection performance.
(8) When turning off the system, be sure to follow the procedures listed below. If the power
supply to the main unit is turned off without shutting down the system, the hard disk may
crash.
(9) When releasing the door lock and opening the front cover, interlock will operate. Do not open
the front cover while the system is in operation unless necessary such as when removing a
PCB.
(10) The lock will be released only when the handle of the front cover is held. When
opening/closing the cover, be sure to hold the handle with two hands.
(11) When opening/closing the front cover, mind your head to avoid hitting the top panel when
entering inside the system as the top panel slides.
(12) When loading/unloading a PCB from the front cover, do not touch the component inside the
system.
(13) When the system is in normal operation, the lock cannot be released even if you hold the
handle of the front cover. The lock can be released only when a dialog that urges you to check
there is no PCB or foreign object remained, or when emergency stop switch is pressed.
(14) Do not turn off the main breaker during system termination processing. Doing so may damage
its hard disk.
(15) Do not repeat turning on/off the power supply. Doing so may cause failure of the main unit. Be
sure to turn on the power supply after at least 3 minutes after the power turned off.
(16) Do not connect to the network or storage device that increases the risk of virus infection.
(17) Do not save the back-ups of inspection programs and libraries on a CR-R/RW or DVD±R/RW,
or their files will become read-only in attribute and fail to work normally when read into this
system.
(18) Since normal operation of this system has been verified in factory settings, do not apply any
OS service pack or security patch, change the settings or update the driver. If you try any
without our consent, it will be construed as a remodeling of the system, and will not be
guaranteed.
(19) Supply air within the specified pressure range (0.3 to 0.6 MPa). Do not use dry air.
6
(20) Use the rated voltage within the power supply specification.
(21) Use a power supply cable conforming to the specifications of the power supply.
(22) Make sure all connectors are connected. Use of any loose connectors could cause loose
connection or occurrence of overcurrent, resulting in fire, smoke or burnout.
(23) Avoid installing the system on a soft floor such as carpet.
(24) Do not conduct check, replacement or adjustment with strained posture.
Notification
This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may take appropriate measures.