MR8740、MR8741_user_manual_eng_20191016H.pdf - 第317页
13.6 Editor Command Details 305 11 Chapter 13 W aveform Evaluation Function (MR8741 Only) 12 13 Fill color Fills in an enclosed area. Instructions 1 Select [Fill color] . 2 Use the mouse to move th e paintbrush mark to t…
13.6 Editor Command Details
304
13.6 Editor Command Details
Load Wave
The waveform shown on the Waveform screen is loaded into the editor and displayed.
Instructions
1
Select [Load Wave].
2
Select the type of waveform capture to perform. The waveform displayed on the
Waveform screen will be loaded into the editor.
3
Select [Load Wave] to exit waveform capture mode.
Zoom in/out
Magnifies or compresses the waveform shown on the screen in the horizontal and ver-
tical directions.
Instructions
1
Select [Zoom in/out].
2
Select whether to magnify or compress the waveform.
3
Set the amount of magnification or compression.
• You can set values with the mouse.
• The amount of movement can be set in 0.04/div steps.
Select
Waveform
capture
Captures the storage waveform displayed on the Waveform screen.
Overlay capture
Captures overlay waveforms shown on the Waveform screen after connecting the uppermost
and lowermost positions with the same display color and filling in the resulting enclosed space.
When the waveforms are overlapping, undisplayed portions of the waveforms cannot be rec-
ognized. This option can be selected when an overlay has been drawn on the screen.
Memory seg-
mentation refer-
ence waveform
Captures the memory segmentation reference waveform shown on the Waveform screen after
connecting the uppermost and lowermost positions with the same display color and filling in
the resulting enclosed space. When the waveforms are overlapping, undisplayed portions of
the waveforms cannot be recognized. This option can be selected when an overlay has been
drawn on the screen.
Execute Performs magnification or compression processing based on the settings and creates an eval-
uation area.
Exit magnifica-
tion/compression
Exits magnification/compression mode.
13.6 Editor Command Details
305
11
Chapter 13 Waveform Evaluation Function (MR8741 Only)
12
13
Fill color
Fills in an enclosed area.
Instructions
1
Select [Fill color].
2
Use the mouse to move the paintbrush mark to the area to be filled in.
If the area is not completely enclosed, adjacent areas will also be filled in.
＋
Execute The area completely enclosed by lines is filled in.
Exit paint
Terminate the paint mode.
Draw shape
Serves to draw a straight, square or a circle.
Instructions
1
Select [Draw shape].
2
Select the figure you wish to draw.
3
Using the mouse, move the mark to the origin of the figure.
4
Selecting [Set] sets the current position as the origin.
5
Moving the mark draws a figure between the origin and the mark.
6
Selecting [Set] again accepts the figure and causes its color to change. For
straight lines, the origin is set at the accepted position. For other types of figure,
accepting the figure has the same effect as selecting
[Cancel].
7
To draw another figure, click [Select] and selecting the figure type.
8
You can repeat steps (3) through (7) to draw figures as desired.
9
Click [Exit Draw shape] to exit figure mode.
＋
＋
＋
13.6 Editor Command Details
306
Eraser
Serves to erase unwanted sections.
Move the mark with the mouse to erase parts of the image.
Instructions
1
Select [Eraser].
2
Use the mouse to move the eraser mark to the start point of the section to be
erased.
3
Clicking [Set] allows you to erase figures while moving the eraser. Clicking [Can-
cel]
allows you to move the eraser without erasing the figures.
4
Move the mark in the [Set] state to erase the parts of figures you don't need.
5
Click [Exit Erase] to terminate the erase mode.
Clear all
Clears the entire editor screen.
Select [Clear all] to clear the editor screen.
Clear select area
Clears a specified rectangular area of the editor screen.
Instructions
1
Select [Clear select area].
2
Using the mouse, move the mark to the origin of the area to be erased.
3
Clicking [Set] sets the position as the origin.
4
Moving the mark displays a rectangle drawn between the origin and the
mark.
5
Clicking [Set] again erases the area inside the rectangle.
Clicking
[Cancel] cancels the position of the origin.
6
Click [Exit Area Clear] to exit area clear mode.
＋
＋
＋