MR8740、MR8741_user_manual_eng_20191016H.pdf - 第318页
13.6 Editor Command Details 306 Eraser Serves to erase unwanted sections. Move the mark with the mouse to erase part s of the image. Instructions 1 Select [Eraser] . 2 Use the mouse to move the eraser mark to the sta rt …
13.6 Editor Command Details
305
11
Chapter 13 Waveform Evaluation Function (MR8741 Only)
12
13
Fill color
Fills in an enclosed area.
Instructions
1
Select [Fill color].
2
Use the mouse to move the paintbrush mark to the area to be filled in.
If the area is not completely enclosed, adjacent areas will also be filled in.
＋
Execute The area completely enclosed by lines is filled in.
Exit paint
Terminate the paint mode.
Draw shape
Serves to draw a straight, square or a circle.
Instructions
1
Select [Draw shape].
2
Select the figure you wish to draw.
3
Using the mouse, move the mark to the origin of the figure.
4
Selecting [Set] sets the current position as the origin.
5
Moving the mark draws a figure between the origin and the mark.
6
Selecting [Set] again accepts the figure and causes its color to change. For
straight lines, the origin is set at the accepted position. For other types of figure,
accepting the figure has the same effect as selecting
[Cancel].
7
To draw another figure, click [Select] and selecting the figure type.
8
You can repeat steps (3) through (7) to draw figures as desired.
9
Click [Exit Draw shape] to exit figure mode.
＋
＋
＋
13.6 Editor Command Details
306
Eraser
Serves to erase unwanted sections.
Move the mark with the mouse to erase parts of the image.
Instructions
1
Select [Eraser].
2
Use the mouse to move the eraser mark to the start point of the section to be
erased.
3
Clicking [Set] allows you to erase figures while moving the eraser. Clicking [Can-
cel]
allows you to move the eraser without erasing the figures.
4
Move the mark in the [Set] state to erase the parts of figures you don't need.
5
Click [Exit Erase] to terminate the erase mode.
Clear all
Clears the entire editor screen.
Select [Clear all] to clear the editor screen.
Clear select area
Clears a specified rectangular area of the editor screen.
Instructions
1
Select [Clear select area].
2
Using the mouse, move the mark to the origin of the area to be erased.
3
Clicking [Set] sets the position as the origin.
4
Moving the mark displays a rectangle drawn between the origin and the
mark.
5
Clicking [Set] again erases the area inside the rectangle.
Clicking
[Cancel] cancels the position of the origin.
6
Click [Exit Area Clear] to exit area clear mode.
＋
＋
＋
13.6 Editor Command Details
307
11
Chapter 13 Waveform Evaluation Function (MR8741 Only)
12
13
Invert colors
Reverses the colors of a filled-in area and the surrounding area.
Select
[Invert colors] to display filled-in area in reverse.
Cancel
Serves to undo the immediately preceding command.
It can be used with commands other than [Save and End] and [Discard and End].
Select
[Cancel] to cancel the editor screen.
Exit
Terminates the editor.
Select [Exit] to select storing evaluation area in memory and quit editor or quitting
editor without storing evaluation area in memory. If
[Exit] is clicked without having
done any editing or immediately after using the store command, the editor is ter-
minated without confirmation.
Note
:The waveform loaded into the editor will be displayed in a different color than
was set with the original settings.
Save and
End
Store evaluation area in memory and quit editor.
See:"4.2 Saving Data" (p.87)
Discard
and End
Quit editor without storing evaluation area in memory. The created area is discarded.