KJ-01.02.Instruction Manual.REV.02.pdf - 第215页

6 − 11 6.2.2.2 A l low able i nput value range for each component type (1) Allowable lead/ball pitc h setting range Component type Lead (ball) pitch Aluminum electrolytic capacitor ― GaAsFET ― SOP 0.3 ～ 1.27mm HSOP 0.3 ～…

100%1 / 419
6 − 10
(4) Vision data on a BGA/FBGA
Setting item Allowable value Description
Pitch Set a value in the same way as a
component having leads on its four sides.
Bend Not settable
Vision PWB
Ceramic
Land
Set the contrast between a ball and a body.
- Against a PWB body, a ball looks white.
- Against a ceramic body, a ball looks
black.
- Land: all lands are to be recognized.
For an FBGA component, you cannot select
“Ceramic”.
Length Not settable Set the length of a lead section that is in
contact with a board.
Ball width
Bottom
See the descriptions of the allowable input
range of the diameter of a ball and the side
to be set.
Ball num.
Bottom/Right
See Table 6.2.22. Set the number of balls located on each
side.
Miss/Miss Not settable.
Table 6.2.2.1.4 Vision data on a BGA/FBGA component
(5) Vision data on an aluminum electrolytic capacitor
Setting item Allowable value Description
Pitch Not settable.
Bend Not settable.
Vision Not settable.
Length See Table 6.2.21. Set the length of a lead section that is in
contact with a board.
Lead width See the descriptions of the allowable input
range of the lead width/ball diameter and
the side to be set.
Set the lead width.
Lead num. Not settable.
Miss/Miss Not settable.
Table 6.2.2.1.5 Vision data on an aluminum electrolytic capacitor
(6) Vision data on GaAsFET
Setting item Allowable value Description
Pitch Not settable.
Bend Not settable.
Vision Not settable.
Length
Bottom/Right
See Table 6.2.21. Set the length of a lead section that is in
contact with a board. The system regards
the right side and left side as the same
side, and the top side and bottom side as
the same side also.
Lead width
Bottom/Right
See the descriptions of the allowable input
range of the lead width/ball diameter and
the side to be set.
Set the lead width.
- The system regards the right side and left
side as the same side, and the top side
and bottom side as the same side also.
Lead num. Not settable.
Miss/Miss Not settable.
6 − 11
6.2.2.2 Allowable input value range for each component type
(1) Allowable lead/ball pitch setting range
Component type Lead (ball) pitch
Aluminum electrolytic capacitor ―
GaAsFET ―
SOP 0.3～1.27mm
HSOP 0.3～1.27mm
SOJ 1.27mm
QFP 0.3～1.27mm
QFJ(PLCC) 1.27mm
BQFP(PQFP) 0.3～1.27mm
TSOP 0.3～1.27mm
TSOP2 0.3～1.27mm
BGA 1.0～3.0mm
FBGA 0.5～2.0mm
CONN 0.3～2.54mm
CON2 0.3～2.54mm
CONZ 0.3～2.54mm
J-lead socket 1.0～1.27mm
Gull-wing socket 1.0～1.27mm
Socket with a bumper 1.0～1.27mm
Outline-to-be-recognized
component
―
Table 6.2.2.2.1 Lead/ball pitch setting range
Note: “
―
“ indicates that any value cannot be entered as a pitch.
6 − 12
(2) Lead length setting range
Component type Input range
Bottom
side
Right
side
Top
side
Left
side
Remarks
Aluminum electrolytic
capacitor
1.5～15.0mm ○ ― ― ― The top side and bottom side are
handled as the same side.
GaAsFET 1.0～15.0mm ○ ○ ― ― Set a value for each side.
SOP 0.3～3.0mm ○ ― ― ― The top side and bottom side are
handled as the same side.
HSOP 0.3～3.0mm ○ ― ― ― The top side and bottom side are
handled as the same side.
SOJ 0.3～3.0mm ○ ― ― ― The top side and bottom side are
handled as the same side.
QFP 0.3～3.0mm ○ ― ― ― The value entered for the bottom side
represents values of all other sides.
QFJ(PLCC) 0.3～3.0mm ○ ― ― ― The value entered for the bottom side
represents values of all other sides.
BQFP(PQFP) 0.3～3.0mm ○ ― ― ― The value entered for the bottom side
represents values of all other sides.
TSOP 0.3～3.0mm ― ○ ― ― The left side and the right side are
handled as the same side.
TSOP2 0.3～3.0mm ○ ― ― ― The top side and bottom side are
handled as the same side.
BGA ― ― ― ― ― Set a value for the top side only.
FBGA ― ― ― ― ―
CONN 0.3～3.0mm ― ― ○ ― Set a value for the top side only.
CON2 0.3～3.0mm ○ ― ○ ― Set the top side and the bottom side
respectively.
CONZ 0.3～3.0mm ○ ― ○ ― Set the top side and the bottom side
respectively.
J-lead socket 0.3～3.0mm ○ ― ― ― The top side and bottom side are
handled as the same side
Gull-wing socket 0.3～3.0mm ○ ― ― ― The top side and bottom side are
handled as the same side
Socket with a bumper 0.3～3.0mm ○ ― ― ― The top side and bottom side are
handled as the same side
Outline-to-be-recogniz
ed component
― ― ― ― ―
Table 6.2.2.2.2 Lead length setting range