KJ-01.02.Instruction Manual.REV.02.pdf - 第407页

11 On Production Control Operations Error No. Error Message Correctiv e Action E5000 Numeric value input area error . The value y ou try to set on the Production conditions menu exceeds the allow able setting range. Chec…

On I/O Manual Operations

Error No. Error Message Corrective Action

W4200 Z position limit over. The entered Z-axis coordinate exceeds the allowable setting

range. Check the allowable range to enter the coordinate

again.

W4231 Can＇t use bad mark sensor.

Please check ＇Installed options

＇ of SETUP.

Although the check box “BAD mark sensor” is not checked

on the “Use unit” menu invoked from the Setup menu, you try

to operate the bad mark device to perform teaching

operation. Check the settings of the “Use unit” menu with

invoking it from the Setup menu.

W4232 Can＇t use BOC. Please check ＇

Installed options

＇

of SETUP.

Although the check box “BOC camera” is not checked on the

“Use unit” menu invoked from the Setup menu, you try to

operate the camera device to perform teaching operation.

Check the settings of the “Use unit” menu with invoking it

from the Setup menu.

W4240 Can＇t use PWB conveyer.

Please check ＇Installed options

＇ of SETUP.

Although the check box “Conveyor connect” is not checked

on the “Use unit” menu invoked from the Setup menu, you try

to operate the automatic board conveyor. Check the

settings of the “Use unit” menu with invoking it from the

Setup menu.

On Production Control Operations

Error No. Error Message Corrective Action

E5000 Numeric value input area error.

The value you try to set on the Production conditions menu

exceeds the allowable setting range. Check the allowable

setting range to set it again.

W5010 PWB data not complete yet.

You tried to use a production program whose PWB data is not

created completely to produce PWBs. Only after creating a

production program with the Data Input command, start PWB

production.

W5011 Placement data not complete yet.

You tried to use a production program whose Placement data

is not created completely to produce PWBs. Only after

creating a production program with the Data Input command,

start PWB production.

W5012 Component data not complete yet.

You tried to use a production program whose Component

data is not created completely to produce PWBs. Only after

creating a production program with the Data Input command,

start PWB production.

W5013 Pick position not complete yet.

You tried to use a production program whose Pick data is not

created completely to produce PWBs. Only after creating a

production program with the Data Input command, start PWB

production.

W5014 Mark data not complete yet.

You tried to use a production program whose mark data is not

created completely to produce PWBs. Only after creating a

production program with the Program Editor, start PWB

production.

W5020 Conveyer reference data unmatch

MS parameter's and PWB data's.

You tried to use a production program created with a machine

whose PWB transport reference is different from this machine

in order to start PWB production.

W5021 Conveyer direction data unmatch

MS parameter's and PWB data's.

You tried to use a production program created with a machine

whose PWB transport direction is different from this machine

in order to start PWB production.

W5022 Shape reference has been

selected in PWB data, but shape

reference unit is not connected to

the machine.

You tried to produce PWBs with using a production program

that uses a shape clamp device although the machine is not

equipped with a shape clamp device or a sh Check the data

with the Data Input command to retry PWB production.ape

clamp device is not set on the Setup menu.

E5023 Planned num. is less than

produced num.

Although you check the check box “Integrate num. of PWBs

produced.” on the “Operation option” menu invoked from the

“Production” menu, you try to set the number that is equal to

the number of PWBs already produced or less as the planned

number of PWBs to be produced.

Set the larger number as the planned number, or clear the

production management information before starting

production.

Or, uncheck the check box “Integrate num. of PWBs

produced.” on the “Operation option” menu.

E5024 Total placement points are within

10,000.

The total number of component placement points per

multiple-plane board is limited to 10000. Decrease the

number of placement points of a circuit or decrease the

number of circuits until total number of placement points

becomes 10000 or less before starting PWB production.

E5025 Don't exist program.

You tried to start PWB production although you had never

loaded any production program into the machine. Only alter

loading a production program into the machine, start PWB

production.

E5026 Integrated PWB number have

reached production plan.

Although you check the check box “Integrate num. of PWBs

produced.” on the “Operation option” menu invoked from the

“Production” menu, you try to produce PWBs with setting the

number of PWBs already produced larger than the planned

number of PWBs to be produced.

Increase the planned number of PWBs to be produced, or

clear the production management information before starting

PWB production.

Or, uncheck the check box “Integrate num. Of PWBs

produced.” on the “Operation option” menu.

E5030 Limit over.(BOC mark points.) You tried to start PWB production with using a production

program that specified the BOC mark coordinates out of the

area components can be placed.

Check the data with the Data Input command to retry

production.

E5031 Limit over.(Placement points.) You tried to start PWB production with using a production

program that specified the component placement coordinates

out of the area components can be placed.

Check the data with the Data Input command to retry

production.

E5032 Limit over.(IC mark points.) You tried to start PWB production with using a production

program that specified the IC mark coordinates out of the

area components can be placed.

Check the data with the Data Input command to retry

production.

E5033 Limit over.(BAD mark points.) You tried to start PWB production with using a production

program that specified the bad mark coordinates out of the

area components can be placed.

Check the data with the Data Input command to retry

production.