KJ-01.02.Instruction Manual.REV.02.pdf - 第417页

21 None LasSetW inParam Bad response to HOf f1. This error message appears on the screen if a communication error occurs when y ou are to set the second measurement start angle to the laser alignment device. Retry this o…

On Laser Operations

Error No. Error Message Corrective Action

None RUN_CMD

Error running Algorithm.

This error message appears on the screen if a communication

error occurs when you are to issue RUN_CMD to the laser

alignment device. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None RESET_CMD

Bad response to RESET_CMD.

This error message appears on the screen if a communication

error occurs when you are to issue RESET_CMD to the laser

alignment device. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None ZERO_CMD

Bad response to ZERO_CMD.

This error message appears on the screen if a communication

error occurs when you are to issue ZERO_CMD to the laser

alignment device. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasSetWinParam

Bad response to WINDOW_CMD.

This error message appears on the screen if a communication

error occurs when you are to issue WINDOW_CMD to the

laser alignment device. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasSetWinParam

Bad response to LeftEdge.

This error message appears on the screen if a

communication error occurs when the machine reads the left

edge of the width that can be recognized with laser by using

the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to RightEdge.

This error message appears on the screen if a

communication error occurs when the machine reads the

right edge of the width that can be recognized with laser by

using the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to Encoder.

This error message appears on the screen if a

communication error occurs when the machine is to read

data from the encoder currently used from the laser

alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again

None LasSetWinParam

Bad response to HOff0.

This error message appears on the screen if a

communication error occurs when you are to set the first

measurement start angle to the laser alignment device. Retry

this operation again. If this error occurs again, return the

machine to its home position. If this error occurs again after

you return the machine to its home position, turn off the

machine, and then turn it on again

None LasSetWinParam

Bad response to HOff1.

This error message appears on the screen if a

communication error occurs when you are to set the second

measurement start angle to the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to ALG0.

This error message appears on the screen if a

communication error occurs when you are to set the first

measurement algorithm to the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to ALG1.

This error message appears on the screen if a

communication error occurs when you are to set the second

measurement algorithm to the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to ALimit0.

This error message appears on the screen if a

communication error occurs when you are to set the first

measurement limit angle to the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to ALimit1.

This error message appears on the screen if a

communication error occurs when you are to set the second

measurement limit angle to the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to

PARAM_CMD.(Pix)

This error message appears on the screen if a

communication error occurs when you are to set the

measurement width-reading unit to the laser alignment

device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to

PARAM_CMD.(Flow)

This error message appears on the screen if a

communication error occurs when you are to set the flow

control to the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to

PARAM_CMD.(Err)

This error message appears on the screen if a

communication error occurs when you are to set the error

level to the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to SysPara

This error message appears on the screen if you cannot set

a system parameter to the laser alignment device.

When one of the three errors described above occurs, this

message appears on the screen. Perform the

corresponding corrective action described above.

None LasSetWinParam

Bad response to LOAD_COM

This error message appears on the screen if a communication

error occurs when you are to issue LOAD_CMD to the laser

alignment device. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasSetWinParam

Bad response to ReadCom.

This error message appears on the screen if a communication

error occurs when you are to issue READ_CMD to the laser

alignment device. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasReadOnce

Error reading once.

This error message appears on the screen if a communication

error occurs when you are to issue ONCE_CMD to the laser

alignment device. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasReport

Unable to read data after 5

attempts. Aborting program.

This error message appears on the screen if a communication

error occurs when the machine is to obtain the result measured

by ONCE_CMD. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasResponse

Error reading ResultData.

This error message appears on the screen if a checksum error

occurs as the result the machine obtains the first measurement

result data. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasResponse

Error reading ResultData2.

This error message appears on the screen if a checksum error

occurs as the result the machine obtains the second

measurement result data. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasSweep

Bad response to SWEEP_CMD.

This error message appears on the screen if a communication

error occurs when you are to issue SWEEP_CMD to the laser

alignment device. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasResponse

Unable to read data after 5

attempts(REPORT_CMD).

Aborting program.

This error message appears on the screen if a communication

error occurs when the machine is to obtain the first

measurement result by SWEEP_CMD. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasResponse

Unable to read data after 5

attempts(REPORTS_CMD).

This error message appears on the screen if a

communication error occurs when the machine is to obtain

the second measurement result by SWEEP_CMD. Retry

this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on

again.