KJ-01.02.Instruction Manual.REV.02.pdf - 第419页

23 None LasHello Bad response to HELLO_CM D. This error message appears on the screen if a communication error occurs when y ou are to issue HELLO_CM D to the laser alignment device. Retry this operation If this error oc…

None LasSetWinParam

Bad response to HOff1.

This error message appears on the screen if a

communication error occurs when you are to set the second

measurement start angle to the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to ALG0.

This error message appears on the screen if a

communication error occurs when you are to set the first

measurement algorithm to the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to ALG1.

This error message appears on the screen if a

communication error occurs when you are to set the second

measurement algorithm to the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to ALimit0.

This error message appears on the screen if a

communication error occurs when you are to set the first

measurement limit angle to the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to ALimit1.

This error message appears on the screen if a

communication error occurs when you are to set the second

measurement limit angle to the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to

PARAM_CMD.(Pix)

This error message appears on the screen if a

communication error occurs when you are to set the

measurement width-reading unit to the laser alignment

device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to

PARAM_CMD.(Flow)

This error message appears on the screen if a

communication error occurs when you are to set the flow

control to the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to

PARAM_CMD.(Err)

This error message appears on the screen if a

communication error occurs when you are to set the error

level to the laser alignment device.

Retry this operation again. If this error occurs again, return

the machine to its home position. If this error occurs again

after you return the machine to its home position, turn off the

machine, and then turn it on again.

None LasSetWinParam

Bad response to SysPara

This error message appears on the screen if you cannot set

a system parameter to the laser alignment device.

When one of the three errors described above occurs, this

message appears on the screen. Perform the

corresponding corrective action described above.

None LasSetWinParam

Bad response to LOAD_COM

This error message appears on the screen if a communication

error occurs when you are to issue LOAD_CMD to the laser

alignment device. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasSetWinParam

Bad response to ReadCom.

This error message appears on the screen if a communication

error occurs when you are to issue READ_CMD to the laser

alignment device. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasReadOnce

Error reading once.

This error message appears on the screen if a communication

error occurs when you are to issue ONCE_CMD to the laser

alignment device. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasReport

Unable to read data after 5

attempts. Aborting program.

This error message appears on the screen if a communication

error occurs when the machine is to obtain the result measured

by ONCE_CMD. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasResponse

Error reading ResultData.

This error message appears on the screen if a checksum error

occurs as the result the machine obtains the first measurement

result data. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasResponse

Error reading ResultData2.

This error message appears on the screen if a checksum error

occurs as the result the machine obtains the second

measurement result data. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasSweep

Bad response to SWEEP_CMD.

This error message appears on the screen if a communication

error occurs when you are to issue SWEEP_CMD to the laser

alignment device. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasResponse

Unable to read data after 5

attempts(REPORT_CMD).

Aborting program.

This error message appears on the screen if a communication

error occurs when the machine is to obtain the first

measurement result by SWEEP_CMD. Retry this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on again.

None LasResponse

Unable to read data after 5

attempts(REPORTS_CMD).

This error message appears on the screen if a

communication error occurs when the machine is to obtain

the second measurement result by SWEEP_CMD. Retry

this operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on

again.

None LasHello

Bad response to HELLO_CMD.

This error message appears on the screen if a

communication error occurs when you are to issue

HELLO_CMD to the laser alignment device. Retry this

operation

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on

again.

None LasReport

LAErr: Data cannot be read from

EEPROM.

This error message appears on the screen if a

communication error occurs when the machine is to read

data from the EEPROM of the laser alignment device. Retry

this operation

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on

again.

None LasReport

LAErr: ImageCheck Err!!!

This error message appears on the screen if a

communication error occurs when you are to issue

IMG_CHK_CMD to the laser alignment device. Retry this

operation.

If this error occurs again, return the machine to its home

position.

If this error occurs again after you return the machine to its

home position, turn off the machine, and then turn it on

again.