KJ-01.02.Instruction Manual.REV.02.pdf - 第314页

8 − 47 T o cancel the pause mode, press the ST ART key to restar t the curr ent Dry run operation, or the STOP key to int errupt it . W hen y ou press the STOP k ey , the Dry run interrupt ion confir mation screen appear…

8 − 46

8.5.2 Display of the production status

When the START key is pressed and the production starts, the status of the

production (the same as that of the board production) appears on the screen.

For details, see “Display of the production status” of the “PC board production”.

Note that production management information is not created.

For the item of “Result”, the number increases with the increasing number of

produced boards but it is not referred to the production management information.

The Pause, Stop, and Quit commands in the execution of the blank run are the same

as those of the board production.

8.5.3

Placement tracking

(1) Automatic run

When “Automatic” is selected in the “Placement camera” field the placement

monitor camera moves over a point of placement after blank run, shoots the

status of placement, and outputs the result to the monitor screen.

The camera stops over the point for a time period set by “Automatic interval”,

then goes to the next point of placement to be monitored.

CAUTION

After blank run, tracking by the camera continues. To avoid a risk of

injury, do not place your hand in the machine, nor move your face or

head close to the machine during operation of the machine.

① To stop the camera

When you press the STOP key or the PAUSE key of the HOD, the machine

pauses at the next component placement point if the camera is moving, or

pauses at the current position if the camera stops. The screen shown in

Figure 8.5.3.1 appears.

Figure 8.5.3.1 “Camera tracking” pause screen in Dry run mode

8 − 47

To cancel the pause mode, press the START key to restart the current Dry run

operation, or the STOP key to interrupt it. When you press the STOP key, the

Dry run interruption confirmation screen appears.

CAUTION

The head starts to move immediately after the START key is pressed,

and then

placement tracking

To avoid a risk of injury, do not place your hand in the machine, nor

move your face or head close to the machine during operation.

Before pressing the START key, check that there is no one who is

working in the machine.

Before pressing the START key, check that there is no one who can

be injured when the head starts to move.

Before pressing the START key, check that there are no obstacles

(tools and jigs) left in the machine.

Even though you press the STOP key to interrupt the current

placement tracking

, the machine replaces a nozzle with another one.

Therefore, the XY-axis and head continue moving.

To prevent you from being injured when you interrupt the

placement

tracking

, do not place your hand in the machine, nor move your face

or head close to the machine while it is operating.

② Changing points of placement

While the machine pauses, press the CAMERA key of the HOD to teach the

component placement position. The machine cannot accept any key of the

HOD other than the CAMERA key.

CAUTION

To avoid a risk of injury, do not place your hand in the machine, nor

move your face or head close to the machine during operation of the

HOD. Note that the head moves to the X and Y coordinates according

the entered values when the cursor is moved after the X and Y values

are entered.

③ Returning to the previous point of placement

While the machine pauses, you can return to the previous point of placement

by pressing the PREVIOUS key of the HOD. The pause status is still held

even after the camera returns to the previous point of placement.

CAUTION

The head starts to move immediately after the PREVIOUS key is

pressed.

To avoid a risk of injury, do not place your hand in the machine, nor

move your face or head close to the machine during operation of the

HOD.

Before pressing the PREVIOUS key, check that there is no one who is

working in the machine.

Before pressing the PREVIOUS key, check that there is no one who

can be injured when the head starts to move.

Before pressing the PREVIOUS key, check that there are no obstacles

(tools and jigs) left in the machine.

8 − 48

④ Moving to the next component placement point

When the machine pauses, press the NEXT key of the HOD, the head

moves to the next component placement position. Even after the head

moves to the next component placement position, the machine keeps

pausing. After you check the last component placement position, the

machine performs the end of production process.

CAUTION

The head starts to move immediately after the NEXT key is pressed.

To avoid a risk of injury, do not place your hand in the machine, nor

move your face or head close to the machine during operation of the

HOD.

Before pressing the NEXT key, check that there is no one who is

working in the machine.

Before pressing the NEXT key, check that there is no one who can be

injured when the head starts to move.

Before pressing the NEXT key, check that there are no obstacles (tools

and jigs) left in the machine.

(2) Manual run

When you select “Manual” as “Place tracking” on the “Trial conditions” screen,

the monitoring camera moves over the first point of placement after blank run,

shoots the status of placement, outputs it to the monitor screen, and pauses

there.

The pause screen for “Manual” is the same as that for “Automatic”.

CAUTION

After blank run has been completed, the camera continues to move to

the the first point of placement. To avoid a risk of injury, do not place

your hand in the machine, nor move your face or head close to the

machine during operation of the HOD.